Turbocharger
Show/hide table
 | |
| Illustration 1 | g03836005 |
Front view | |
Show/hide table
| Specification for 284-5380 Turbocharger Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| 1 | 16 | 2N-2765 High Temperature Bolt | Before assembly, apply Loctite C5A Copper Anti-Seize to the washer face and to the threads. Torque to 55 ± 10 N·m (41 ± 7 lb ft). |
Show/hide table
 | |
| Illustration 2 | g03836004 |
Right side view | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 2 | 4 | 239-5858 Compressor Clamp Assembly | Before assembly, apply Loctite C5A Copper Anti-Seize to the threads. Use the following procedure in order to tighten clamp assemblies for the cartridges: 1. Tighten the clamp assemblies to 14.0 ± 1.5 N·m (123.9 ± 13.3 lb in). 2. Gently tap around the clamp assemblies with a soft faced hammer. 3. Again tighten the clamp assemblies to 14.0 ± 1.5 N·m (123.9 ± 13.3 lb in). |
| 3 | 4 | 9N-2038 Turbine Clamp As | |
| 4 | 2 | 214-6050 Clamp | Use the following procedure in order to tighten the clamps: 1. Tighten the clamps to 20 ± 1 N·m (177 ± 9 lb in). 2. Gently tap around the clamps with a soft faced hammer. 3. Again tighten the clamps to 20 ± 1 N·m (177 ± 9 lb in). |
| 5 | 2 | 306-1720 Band Clamp |
Caterpillar Information System:
C11 and C13 Engines Turbocharger
C11 and C13 Engines Turbocharger
345D Excavator and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Relief Valve (Main) - Heavy Lift
2008/03/17 Improved Fastening for the Turbocharger to the Exhaust Manifold {1052, 1053}
307E2 Mini Hydraulic Excavator Machine System Specifications Bucket Linkage
C7 PETROLEUM Petroleum Engine Crankcase Breather - Remove and Install
345D, 349D and 349D2 Excavators Hydraulic System Negative Flow Control System
793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Pressure Switch (Hydraulic Fan, Steering Oil Filter)
345D, 349D and 349D2 Excavators Hydraulic System Main Control Valve
G3520B Industrial Engines Engine Control Panel
C7 PETROLEUM Petroleum Engine Exhaust Manifold - Remove and Install
793F and 793F CMD Off-Highway Truck Braking System Pump Drive Shaft
C18 Marine Engines Configuration Parameters
345D, 349D and 349D2 Excavators Hydraulic System Boom Hydraulic System
G3520B Industrial Engines General Information (Electronic Control System)
Salvage of Center Bearing in Torque Converter Input Housing {3101, 3127} Salvage of Center Bearing in Torque Converter Input Housing {3101, 3127}
G3520B Industrial Engines Ignition Transformer
G3520B Engines Gear Group (Front)
3500 Engines Exhaust Manifold
G3520B Industrial Engines Fuel Shutoff - Test
G3520B Industrial Engines Timing Offset - Calibration
3500 Engines Air Inlet and Exhaust Lines
G3500 Engines Engine Oil Pump
3176C, 3406E and 3456 Industrial Engines Speed Control - Test