Turbocharger - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 5P-3931 | Anti-Seize Compound | - |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (A) to the turbocharger mounting studs on the exhaust manifold.
Show/hide table
Illustration 1 g01456857 - Attach a suitable lifting device to turbocharger (2). The weight of turbocharger (2) is approximately
23 kg (50 lb) . Position the gasket and turbocharger (2) on the exhaust manifold.Note: Discard the nuts after use. Use new nuts for installation.
- Install nuts (7). Tighten nuts (7) to a torque of
54 ± 5 N·m (40 ± 4 lb ft) . - Connect hose (4) and tube assembly (3).
- Position tube assembly (5) and install bolts (6). Connect hose assembly (1).
- Refill the coolant system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Caterpillar Information System:
Failure of Reused Rotocoils in 3500 Engines{1100} Failure of Reused Rotocoils in 3500 Engines{1100}
345D, 349D and 349D2 Excavators Hydraulic System Main Hydraulic Pump
345D, 349D and 349D2 Excavators Hydraulic System Hydraulic Filter (Pilot)
345D, 349D and 349D2 Excavators Hydraulic System Gear Pump (Pilot)
2008/07/14 Some Gasket Kits are Reinstated and Some New Gasket Kits are Available {1000, 1100}
Procedure to Access the Timing Pin Hole for Installation of the High Pressure Fuel Injection Pump{1251} Procedure to Access the Timing Pin Hole for Installation of the High Pressure Fuel Injection Pump{1251}
C7 PETROLEUM Petroleum Engine Turbocharger - Remove
Storage Procedure for Caterpillar Products {1000, 1250, 1350} Storage Procedure for Caterpillar Products {1000, 1250, 1350}
2008/03/01 Procedure to Access the Timing Pin Hole for the High Pressure Fuel Injection Pump {1251}
345D, 349D and 349D2 Excavators Hydraulic System Pilot Hydraulic System
2008/03/01 A New Guide Spring for the Camshaft Lifter is Now Used {1102}
2008/03/17 A New Guide Spring for the Camshaft Lifter is Now Used {1102}
G3520B Industrial Engines Air/Fuel Ratio Control - Adjust - NO<SUB>X</SUB> Feedback
793F and 793F CMD Off-Highway Truck Braking System Pump Drive Shaft
C7 PETROLEUM Petroleum Engine Exhaust Manifold - Remove and Install
G3520B Industrial Engines Engine Control Panel
345D, 349D and 349D2 Excavators Hydraulic System Main Control Valve
793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Pressure Switch (Hydraulic Fan, Steering Oil Filter)
345D, 349D and 349D2 Excavators Hydraulic System Negative Flow Control System
C7 PETROLEUM Petroleum Engine Crankcase Breather - Remove and Install
307E2 Mini Hydraulic Excavator Machine System Specifications Bucket Linkage
2008/03/17 Improved Fastening for the Turbocharger to the Exhaust Manifold {1052, 1053}
345D Excavator and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Relief Valve (Main) - Heavy Lift
C11 and C13 Engines Turbocharger