Engine Oil Pan
Show/hide table
 | |
| Illustration 1 | g03330203 |
Typical example | |
Show/hide table
| Specification for 198-6368 Oil Pan Gp and 197-6354 Oil Pan Gp | |||
| Item | Qty | Part | Specification Description |
| The sealing surfaces of the oil pan shall be free of oil, debris, gasket material that is protruding, or any other sealant. The oil pan must be assembled and tightened to the cylinder block within 10 minutes of applying sealant. | |||
| - | - | - | Apply, Loctite RTV silicone to a bead of 5 mm (0.2 inch) at two places: To the connecting joint of the front housing (3) . and to the connecting joint of the flywheel housing (4) . |
| - | - | - | Use the following tightening procedure for oil pan bolts: Tighten the four bolts (1) . Start with bolt (2) and tighten rest all bolts in a counterclockwise sequence. Again, start with bolt (2) and tighten all the bolts in a counterclockwise sequence to 31 ± 3 N·m (274 ± 27 lb in). |
Caterpillar Information System:
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0168 - FMI 03
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Connector Contact Identification of Generator Set Control
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Block Diagram of Generator Set Control
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Speed Sensor (Engine) - Adjust
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Alarm Module Control - Adjust
G3600 Engines Air/Fuel Pressure Module - Calibrate
G3600 Engines ECM - Replace
2009/08/03 Procedure for Providing Constant Power to the Electronic Control Module (ECM) {1408, 1901}
G3600 Engines Electronic Service Tool Does Not Communicate
SR5 Electric Power Generation Generator Fan - Remove and Install
C3.3 Industrial Engine Accessory Drive - Install
C3.3 Industrial Engine Accessory Drive - Assemble
Inspection of Diesel Particulate Filters (DPF), Diesel Oxidation Catalysts (DOC) and CRS Bodies {108F, 1091} Inspection of Diesel Particulate Filters (DPF), Diesel Oxidation Catalysts (DOC) and CRS Bodies {108F, 1091}
2008/02/25 Procedure for Installing the Front Gears and Dampers on Certain Caterpillar Engines {1151, 1162, 1205, 1206}
2008/02/01 Procedure for Installing the Front Gears and Dampers on Certain Caterpillar Engines {1151, 1162, 1205, 1206}
C27 and C32 Industrial Engines Configuration Parameters
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Electrical Connector - Inspect
The Intake Valve Actuator has Current Low Faults on the C13 Engine{1901, 1902, 7620} The Intake Valve Actuator has Current Low Faults on the C13 Engine{1901, 1902, 7620}
False Event for High Boost Pressure in some 3500B and 3500C Engines Used in Electric Power Generation and Industrial Applications{1052, 1901, 1917} False Event for High Boost Pressure in some 3500B and 3500C Engines Used in Electric Power Generation and Industrial Applications{1052, 1901, 1917}
C11 and C13 Engines for Caterpillar Built Machines Crankshaft - Install
C11 and C13 Petroleum Engines Crankshaft Main Bearings - Install
C13T-TH35 and C15T-TH35 Petroleum Packages Product Lifting
C7 Petroleum Engines Electric Starting Motor
C13, C15, and C18 Tier 4 Final Engines Turbocharger