Accessory Drive - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
C | 207-1601 | Rubber Lubricant | 1 |
D | 9S-3263 | Thread Lock Compound | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect the bore in front housing (3) for damage. If necessary, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install".
- Lightly lubricate a new O-ring seal (5) (not shown) with Tooling (C). Install the O-ring seal (not shown) into the groove in accessory drive housing (4).
- Lightly lubricate bearing (6), bearing (8), and gear (7) with clean engine lubricating oil. Install the assembly of the accessory drive to the front housing. Ensure that the flange on the accessory drive housing is flush with the front housing.
- Apply Tooling (D) to allen head screws (1) and allen head screw (2).
- Install allen head screws (1) and allen head screw (2) to accessory drive housing (4).
- Tighten allen head screws (1) to a torque of
22 N·m (16 lb ft) .Tighten allen head screw (2) to a torque of
44 N·m (32 lb ft) . Tighten allen head screws (1) and (2) in the sequence that is shown in Illustration 2. - Ensure that there is tactile backlash between the idler gear and the accessory drive gear.
Show/hide table
Illustration 1 | g01441026 |
Typical example |
Show/hide table
Illustration 2 | g01444555 |
Sequence for tightening accessory drive |
Caterpillar Information System:
C3.3 Industrial Engine Accessory Drive - Assemble
C3.3 Industrial Engine Accessory Drive - Disassemble
C3.3 Industrial Engine Accessory Drive - Remove
G3600 Engines Electrical Connectors
C9 Petroleum Engines Engine Oil Pan
C11 and C13 Petroleum Engines Engine Design
325D and 329D Excavators Machine System Specifications Drain Line (Muffler)
G3600 Engines Component Location
C18 Petroleum Generator Sets Refill Capacities and Recommendations
G3600 Engines Oil Pressure Is High
2008/01/28 A New Adapter Assembly is Used with the Turbocharger Compressor Outlet Pressure Sensor {1917}
C7 Petroleum Engines Fuel Priming Pump
SR5 Electric Power Generation Generator Fan - Remove and Install
G3600 Engines Electronic Service Tool Does Not Communicate
2009/08/03 Procedure for Providing Constant Power to the Electronic Control Module (ECM) {1408, 1901}
G3600 Engines ECM - Replace
G3600 Engines Air/Fuel Pressure Module - Calibrate
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Alarm Module Control - Adjust
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Speed Sensor (Engine) - Adjust
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Block Diagram of Generator Set Control
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Connector Contact Identification of Generator Set Control
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0168 - FMI 03
C9 On-highway Engine Engine Oil Pan
Inspection of Diesel Particulate Filters (DPF), Diesel Oxidation Catalysts (DOC) and CRS Bodies {108F, 1091} Inspection of Diesel Particulate Filters (DPF), Diesel Oxidation Catalysts (DOC) and CRS Bodies {108F, 1091}