Electrical Connectors
接线盒
Show/hide table
图 1 | g00891827 |
接线盒 |
发动机接线盒位于发动机的右后侧。 电子控制模块(ECM)位于接线盒内。 接线盒为所有与发动机传感器和点火系统相关的接线提供接线端点。
Show/hide table
图 2 | g00892898 |
接线盒内部 (J2/P2) 70 针 ECM 接头 (J1/P1) 70 针 ECM 接头 (1) 接地母线 (2) 24 VDC 电源接线端 (J7) 9 针维修工具接头 (CB1) 16 安培断路器 (CB2) 6 安培断路器 (J3/P3) 70 针客户接线接头 (3) V 型发动机左侧的点火接线 (J6/P6) 发动机左侧传感器的 70 针接头 (J5/P5) 发动机右侧传感器的 70 针接头 (4) V 型发动机右侧的点火接线 (J4) 选装控制面板或客户接头的 47 针接头 (5) 电源接线 |
Show/hide table
图 3 | g00891953 |
接线盒前部和底部 (J6) 发动机左侧传感器的 70 针接头 (J5) 发动机右侧传感器的 70 针接头 (J4) 选装控制面板或客户接头的 47 针接头 (6) 紧急停机按钮 (7) V 型发动机左侧的点火接线孔 (8) V 型发动机右侧的点火接线孔 (9) 电源孔和/或通往 70 针接头的客户接线孔 (P3) |
接头
Show/hide table
图 4 | g01450202 |
ECM 和接线盒上的 70 针接头 |
Show/hide table
图 5 | g01450246 |
接线盒底部的 P4 接头 |
Show/hide table
图 6 | g01431259 |
各种传感器的线束接头 (A) 5 V 电源 (B) 回路 (C) 信号 |
Caterpillar Information System:
C9 Petroleum Engines Engine Oil Pan
C11 and C13 Petroleum Engines Engine Design
325D and 329D Excavators Machine System Specifications Drain Line (Muffler)
G3600 Engines Component Location
C18 Petroleum Generator Sets Refill Capacities and Recommendations
G3600 Engines Oil Pressure Is High
2008/01/28 A New Adapter Assembly is Used with the Turbocharger Compressor Outlet Pressure Sensor {1917}
C7 Petroleum Engines Fuel Priming Pump
345D, 349D and 349D2 Excavator Machine System Specifications Upper Frame
C7 Petroleum Engines Refrigerant Compressor
2008/02/18 Procedure for the Return of Marine Engine Parts {1000}
C11 and C13 Petroleum Engines Belt Tensioner
C3.3 Industrial Engine Accessory Drive - Remove
C3.3 Industrial Engine Accessory Drive - Disassemble
C3.3 Industrial Engine Accessory Drive - Assemble
C3.3 Industrial Engine Accessory Drive - Install
SR5 Electric Power Generation Generator Fan - Remove and Install
G3600 Engines Electronic Service Tool Does Not Communicate
2009/08/03 Procedure for Providing Constant Power to the Electronic Control Module (ECM) {1408, 1901}
G3600 Engines ECM - Replace
G3600 Engines Air/Fuel Pressure Module - Calibrate
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Alarm Module Control - Adjust
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Speed Sensor (Engine) - Adjust
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Block Diagram of Generator Set Control