Hydraulic Tank - Assemble
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 456-4371 | Lever Hoist As. | 1 |
| B | 439-3938 | Link Bracket | 2 |
- Install rectangular seal (26), valve (25), spring (24), and valve guide (23) into drain valve body (22).
Show/hide table
Illustration 2 g06351929 - Install drain assembly (20) and bolts (21).
Show/hide table
Illustration 3 g06351913 Show/hide table
Illustration 4 g06351750 - Attach Tooling (A), Tooling (B), and a suitable lifting device to the hydraulic tank. The weight of the hydraulic tank is approximately
82 kg (180 lb) . - Rotate the hydraulic tank, as shown.
Show/hide table
Illustration 5 g06351685 - Install screen (19), bolts (18), and the nuts.
Show/hide table
Illustration 6 g06351655 - Install screen (17), the bolts, and nuts (16).
Show/hide table
Illustration 7 g06351391 Show/hide table
Illustration 8 g06351390 - Install plate (14) and three bolts (15).
Show/hide table
Illustration 9 g06351386 Show/hide table
Illustration 10 g06351383 - Install glass (12), plate (13), retainer (11), and nuts (10). Tighten nuts (10) to a torque of
30 ± 5 N·m (266 ± 44 lb in) .Show/hide table
Illustration 11 g06351376 - Install seal (9) onto cover (8).
Show/hide table
Illustration 12 g06351373 - Install cover (8) and nuts (7).
Show/hide table
Illustration 13 g06351719 - Install strainer assembly (6) and retaining ring (5).
Show/hide table
Illustration 14 g06351716 - Install cap assembly (4).
Show/hide table
Illustration 15 g06351367 - Install pressure switch (3). Tighten pressure switch (3) to a torque of
48 ± 5 N·m (35 ± 4 lb ft) . - Install temperature sensor (2). Tighten temperature switch (2) to a torque of
20 ± 3 N·m (177 ± 27 lb in) . - Install breaker relief valve (1).
Show/hide table
| |
| Illustration 1 | g06351933 |
Show/hide table
 |
|
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
End By:
- Install the hydraulic tank.
Caterpillar Information System:
D6 Track-Type Tractor Winch Wire Rope - Install - If Equipped
D6 Track-Type Tractor Undercarriage - Clean
D6 Track-Type Tractor Fuel System - Prime
910M, 914M and 918M Wheel Loader Power Train Axle (Front) - Remove and Install
D6 Track-Type Tractor Ether Starting Aid Cylinder - Replace
910M, 914M and 918M Wheel Loader Power Train Axle (Front) - Remove and Install
910M, 914M and 918M Wheel Loader Power Train Axle (Rear) - Remove and Install
2D, 2D Advanced, and 3D GRADE System for Next Gen Hydraulic Excavators Electrical Connector - Inspect
D3K2, D4K2 and D5K2 Track-Type Tractors Belts - Replace
D6 Track-Type Tractor Engine Supplement Diesel Exhaust Fluid Module - Remove and Install
The Push Frame Cover Group Has Been Improved and Now Used on Certain 631K Wheel Tractor-Scrapers {0679, 7254, 726A} The Push Frame Cover Group Has Been Improved and Now Used on Certain 631K Wheel Tractor-Scrapers {0679, 7254, 726A}
D6 Track-Type Tractor Engine Supplement Battery - Remove and Install
Installation of the 567-0669 Coupler Lines Gp on Certain Wheel Loaders {5057, 5133, 6129} Installation of the 567-0669 Coupler Lines Gp on Certain Wheel Loaders {5057, 5133, 6129}
C175-16 Locomotive Engine Diesel Exhaust Fluid Pump Diaphragm - Replace
C175-16 Locomotive Engine Diesel Exhaust Fluid Pump Check Valves - Replace
C175-16 Locomotive Engine Crankshaft Vibration Damper Bolts - Inspect
C175-16 Locomotive Engine Crankshaft Vibration Damper seals - Replace
C175-16 Locomotive Engine Diesel Exhaust Fluid System - Inspect/Clean
D6 Track-Type Tractor Machine Systems Piston Pump (Steering) - Remove and Install
D8T Track-Type Tractor Differential Steering System
C175-16 Locomotive Engine Fuel Injector - Replace
D11 Track-Type Tractor Power Train System Screens - Clean
Cat® Command for Dozing, Remote Control Operator Station Operator Station Action Alarm - Check
D6 XE Track-Type Tractor Power Train Electric Drive Wiring - Remove and Install