Axle (Rear) - Remove and Install
Start By:
- Remove the rear tires.
- Drain the rear axle into a suitable container.
Show/hide table
Illustration 1 g06102697 - Disconnect grease line (2). Repeat for the opposite side.
- Remove bolts (1) and disconnect the drive shaft.
Show/hide table
Illustration 2 g06102703 - Disconnect hose assemblies (3) and (4).
Show/hide table
Illustration 3 g06102707 - Position suitable cribbing and a jack under the rear axle. The weight of the rear axle is approximately
376 kg (830 lb) . Remove bolts (5) and slowly lower the rear axle from the machine.
- Install the rear axle in the reverse of removal.
- Tighten bolts (5) to a maximum torque of
350 N·m (258 lb ft) to ensure full engagement of the trunnion dowels into the frame. Loosen bolts (5) by a minimum of one full turn. Tighten bolts (5) in the sequence shown to340 ± 40 N·m (250 ± 30 lb ft) . Turn bolts (5) in the sequence shown an additional 180° ± 5°.
Show/hide tableIllustration 4 g06351835 - Tighten bolts (5) to a maximum torque of
- Clean the bearing cap and yoke mounting faces of the drive shaft. Snug bolts (1) and then tighten bolts (1) to a torque of
60 ± 7 N·m (44 ± 5 lb ft) .
Caterpillar Information System:
2D, 2D Advanced, and 3D GRADE System for Next Gen Hydraulic Excavators Electrical Connector - Inspect
D3K2, D4K2 and D5K2 Track-Type Tractors Belts - Replace
D6 Track-Type Tractor Engine Supplement Diesel Exhaust Fluid Module - Remove and Install
The Push Frame Cover Group Has Been Improved and Now Used on Certain 631K Wheel Tractor-Scrapers {0679, 7254, 726A} The Push Frame Cover Group Has Been Improved and Now Used on Certain 631K Wheel Tractor-Scrapers {0679, 7254, 726A}
D6 Track-Type Tractor Engine Supplement Battery - Remove and Install
Procedure to Improve the Push Frame Cover Group on Certain 631KWheel Tractor-Scrapers {0679, 7254, 726A} Procedure to Improve the Push Frame Cover Group on Certain 631KWheel Tractor-Scrapers {0679, 7254, 726A}
D6 Track-Type Tractor Machine Systems Hydraulic Tank - Disassemble
D3K2, D4K2 and D5K2 Track-Type Tractors Undercarriage - Clean
A New Cylinder Liner is Now Used on Certain C18 and C32 Machine Engines {1201} A New Cylinder Liner is Now Used on Certain C18 and C32 Machine Engines {1201}
D3K2, D4K2 and D5K2 Track-Type Tractors Cab Filter (Fresh Air) - Replace
D10T2 Track-Type Tractor Plate Locations and Film Locations
D6 Track-Type Tractor Machine Systems Hydraulic Tank - Remove and Install
910M, 914M and 918M Wheel Loader Power Train Axle (Front) - Remove and Install
D6 Track-Type Tractor Ether Starting Aid Cylinder - Replace
910M, 914M and 918M Wheel Loader Power Train Axle (Front) - Remove and Install
D6 Track-Type Tractor Fuel System - Prime
D6 Track-Type Tractor Undercarriage - Clean
D6 Track-Type Tractor Winch Wire Rope - Install - If Equipped
D6 Track-Type Tractor Machine Systems Hydraulic Tank - Assemble
Installation of the 567-0669 Coupler Lines Gp on Certain Wheel Loaders {5057, 5133, 6129} Installation of the 567-0669 Coupler Lines Gp on Certain Wheel Loaders {5057, 5133, 6129}
C175-16 Locomotive Engine Diesel Exhaust Fluid Pump Diaphragm - Replace
C175-16 Locomotive Engine Diesel Exhaust Fluid Pump Check Valves - Replace
C175-16 Locomotive Engine Crankshaft Vibration Damper Bolts - Inspect
C175-16 Locomotive Engine Crankshaft Vibration Damper seals - Replace