Flywheel Housing - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7575 | Link Bracket | 2 |
B | - | Guide Bolts M12 x 1.75 by 120 mm |
2 |
Start By:
- Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
- Remove the electric starting motor, if necessary. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
- Remove two bolts (2). Install Tooling (B) in the cylinder block.
- Attach Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of flywheel housing (1) is approximately
55 kg (121 lb) . - Remove remaining bolts (2).
- Remove bolts (3) (not shown) that fasten the engine oil pan to flywheel housing (1). Remove flywheel housing (1).
Show/hide table
Illustration 1 | g01434695 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7575 | Link Bracket | 2 |
B | - | Guide Bolts M12 x 1.75 by 120 mm |
2 |
C | 1U-8846 | Gasket Sealant | 1 |
- Apply Tooling (C) to the entire mounting surface of the flywheel housing prior to installation. The flywheel housing must be installed within 10 minutes of application.
Show/hide table
Illustration 2 g01434695 - Install Tooling (B) in the cylinder block.
- Attach Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of flywheel housing (1) is approximately
55 kg (121 lb) . Position flywheel housing (1) on Tooling (B). - Install bolts (2). Remove Tooling (B) and install remaining bolts (2).
- Install bolts (3) (not shown) that fasten the engine oil pan to flywheel housing (1).
End By:
- Install the electric starting motor, if necessary. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
- Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Caterpillar Information System:
C15 and C18 Petroleum Generator Sets Overhaul (Top End)
C15 and C18 Petroleum Generator Sets Overhaul (Major)
C9 Petroleum Engines Flywheel - Remove and Install
C18 Petroleum Generator Sets Fuel System - Prime
C15 and C18 Petroleum Generator Sets Fuel System - Prime
C9 Industrial Engines Exhaust Manifold
G3520C and G3520E Engines Air Lines - Compressor Bypass
345B Series II Excavator Machine System Specifications Travel Motor
3176C, 3406E and 3456 Industrial Engines Timing - Calibrate
3176C, 3406E and 3456 Industrial Engines Throttle Position Sensor - Calibrate
325D and 329D Excavators and 325D Material Handler Machine System Specifications Joystick Control
2008/01/28 A New Floating Aftercooler Core is Now Used {1063, 1380, 3319}
3176C, 3406E and 3456 Industrial Engines Electronic Service Tool Does Not Communicate
3176C, 3406E and 3456 Industrial Engines Indicator Lamp - Test
C13, C15, and C18 Tier 4 Final Engines Air Lines
3176C, 3406E and 3456 Industrial Engines Coolant Level - Test
C4.4 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
3176C, 3406E and 3456 Industrial Engines Engine Overspeeds
C9 Petroleum Engines Front Cover - Remove and Install
3176C, 3406E and 3456 Industrial Engines Diagnostic Code Cross Reference
C18 Petroleum Generator Sets Instrument Panel - Inspect
C27 and C32 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Parallel Setpoint Viewing OP2-3
C9 Petroleum Engines Gear Group (Front) - Remove