Throttle Position Sensor - Calibrate
如果表 1 中的诊断代码激活,采用此步骤。
Show/hide table
诊断代码表     | ||
---|---|---|
代码和描述     | 产生此代码的状况     | 系统响应     |
91-13 油门位置传感器:需要标定     | 油门位置传感器信号的占空比低于5%或高于95%。     | 该诊断代码激活时,电子控制模块(ECM)将理想发动机转速设定为编程设定的低怠速。 该诊断代码激活时,Caterpillar 电子技师(ET)将会指示油门位置为 0%。     |
操作时,油门操纵杆系应无发卡或阻力过大现象。 需要使用 Cat ET 来对油门位置传感器进行标定。
- 检查油门连杆是否损坏。
- 断开 ECM 的电源。
- 检查油门操纵杆系部件有无下列情况:
- 松动
- 弯曲
- 折断
- 丢失的
- 磨损
修理任何损坏的部件。
- 松动
- 调整油门连杆以获得低怠速。
- 将 Cat ET 连接到维修工具接头上。
- 恢复 ECM 的电源。 不要启动发动机。
- 在 Cat ET上观察油门位置。
- 将油门控制置于低怠速位置。 调整油门连杆或低怠速调整螺钉,直到 Cat ET 上的油门位置显示为 0%。
当油门处于低怠速位置时,油门位置传感器的工作负载循环为 5% 至 10%。 ECM 将该 5% 至 10% 的工作负载循环转换为 0% 的油门位置。
- 调整油门连杆以获得高怠速。
- 将油门控制置于高怠速位置。 调整油门连杆或高怠速调整螺钉,直到 Cat ET 上的油门位置显示为 100%。
当油门处于高怠速位置时,油门位置传感器的工作负载循环为 90% 至 95%。 ECM 将该 90% 至 95% 的工作负载循环转换为 100% 的油门位置。
将油门从低怠速位置调整到高怠速位置。 在 CatET上监测油门位置。 如果 Cat ET 上的油门位置不显示 0% 至 100% 的读数,再次执行该步骤。
- 将油门控制置于高怠速位置。 调整油门连杆或高怠速调整螺钉,直到 Cat ET 上的油门位置显示为 100%。
Caterpillar Information System:
325D and 329D Excavators and 325D Material Handler Machine System Specifications Joystick Control
2008/01/28 A New Floating Aftercooler Core is Now Used {1063, 1380, 3319}
C15 and C18 Petroleum Generator Sets Product Description
2007/11/19 Improvements Made To Connectors For The EMCP3 Control Panel {4490}
C3.3 Industrial Engine Safety Messages
G3500B Engines Engine Oil Filter - Duplex
320D and 323D Excavators Machine System Specifications Joystick Control
C9 Petroleum Engines Water Temperature Regulator - Remove and Install
C15 and C18 Petroleum Generator Sets Plate Locations and Film Locations
C18 Petroleum Generator Sets Plate Locations and Film Locations
C9 Petroleum Engines Water Pump - Install
2007/11/19 The Air Filter Element Assembly is Updated {1051, 1054}
3176C, 3406E and 3456 Industrial Engines Timing - Calibrate
345B Series II Excavator Machine System Specifications Travel Motor
G3520C and G3520E Engines Air Lines - Compressor Bypass
C9 Industrial Engines Exhaust Manifold
C15 and C18 Petroleum Generator Sets Fuel System - Prime
C18 Petroleum Generator Sets Fuel System - Prime
C9 Petroleum Engines Flywheel - Remove and Install
C15 and C18 Petroleum Generator Sets Overhaul (Major)
C15 and C18 Petroleum Generator Sets Overhaul (Top End)
C9 Petroleum Engines Flywheel Housing - Remove and Install
3176C, 3406E and 3456 Industrial Engines Electronic Service Tool Does Not Communicate
3176C, 3406E and 3456 Industrial Engines Indicator Lamp - Test