Travel Motor
Show/hide table
图 1 | g01434339 |
Show/hide table
注意 |
---|
为防止损坏马达,操作前壳体内必须加注干净的液压油,至少加注到加注口。 |
(1) 螺塞的扭矩 ... 430 ± 40 N·m (320 ± 30 lb ft)
(2) 使用 1U-6396 O 形密封圈组件附着剂 润滑 O 形密封圈。
组装前,利用干净的液压油轻轻润滑活塞 (3) 、凸轮板 (4) 、套筒 (6) 、轴 (8) 、球阀 (11) 和活塞 (12) 的滑动表面。
(5) 请参阅插图 1 了解 4 个弹簧垫圈的备用方向。
(7) 124-1561 制动器弹簧
- 数量 ... 20
- 在试验力下的长度 ... 19.0 mm (0.75 in)
- 试验力 ... 425 ± 43 N (95.5 ± 9.7 lb)
- 试验后的自由长度 ... 22.06 mm (0.869 in)
- 外径 ... 23.0 mm (0.91 in)
- 在试验力下的长度 ... 19.0 mm (0.75 in)
(9) 将 4C-4030 螺纹锁固胶 涂敷在唇形油封杯的外径上。
(10) 朝向轴法兰安装专用座圈轴承的卡环。
(13) 三只 O 形密封螺塞的扭矩 ... 82 ± 8 N·m (60 ± 6 lb ft)
(14) 6 个螺栓的扭矩 ... 530 ± 70 N·m (390 ± 50 lb ft)
(15) 2 个 O 形圈螺塞的扭矩 ... 190 ± 20 N·m (140 ± 15 lb ft)
Show/hide table
图 2 | g01434338 |
剖面 A-A |
(16) 在节流孔中朝向泵头表面或在泵头表面以下安装管塞。
(17) 124-1554 弹簧
- 在试验力下的长度 ... 15 mm (0.6 in)
- 试验力 ... 15 ± 2 N (3.4 ± 0.4 lb)
- 试验后的自由长度 ... 16.15 mm (0.636 in)
- 外径 ... 5.50 mm (0.217 in)
- 试验力 ... 15 ± 2 N (3.4 ± 0.4 lb)
(18) 节流孔螺塞的扭矩 ... 7 ± 1 N·m (60 ± 9 lb in)
(D) 泵头深度和配流盘接口 ... 25.63 ± 0.20 mm (1.009 ± 0.008 in)
Show/hide table
图 3 | g01435172 |
剖面 C-C |
(19) 转速控制阀总成的扭矩 ... 50 ± 3 N·m (37 ± 2 lb ft)
Caterpillar Information System:
3176C, 3406E and 3456 Industrial Engines Timing - Calibrate
3176C, 3406E and 3456 Industrial Engines Throttle Position Sensor - Calibrate
325D and 329D Excavators and 325D Material Handler Machine System Specifications Joystick Control
2008/01/28 A New Floating Aftercooler Core is Now Used {1063, 1380, 3319}
C15 and C18 Petroleum Generator Sets Product Description
2007/11/19 Improvements Made To Connectors For The EMCP3 Control Panel {4490}
C3.3 Industrial Engine Safety Messages
G3500B Engines Engine Oil Filter - Duplex
320D and 323D Excavators Machine System Specifications Joystick Control
C9 Petroleum Engines Water Temperature Regulator - Remove and Install
C15 and C18 Petroleum Generator Sets Plate Locations and Film Locations
C18 Petroleum Generator Sets Plate Locations and Film Locations
G3520C and G3520E Engines Air Lines - Compressor Bypass
C9 Industrial Engines Exhaust Manifold
C15 and C18 Petroleum Generator Sets Fuel System - Prime
C18 Petroleum Generator Sets Fuel System - Prime
C9 Petroleum Engines Flywheel - Remove and Install
C15 and C18 Petroleum Generator Sets Overhaul (Major)
C15 and C18 Petroleum Generator Sets Overhaul (Top End)
C9 Petroleum Engines Flywheel Housing - Remove and Install
3176C, 3406E and 3456 Industrial Engines Electronic Service Tool Does Not Communicate
3176C, 3406E and 3456 Industrial Engines Indicator Lamp - Test
C13, C15, and C18 Tier 4 Final Engines Air Lines
3176C, 3406E and 3456 Industrial Engines Coolant Level - Test