Front Cover - Remove and Install
Start By:
- Remove the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
- Remove the fan drive, if necessary. Refer to Disassembly and Assembly, "Fan Drive - Remove".
- Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Remove".
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Support the attachment for the accessory drive and remove bolts (2).
- Remove bolts (1). Remove front cover (3) and the gasket.
Show/hide table
| |
| Illustration 1 | g01173620 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: The rear face of the front cover and the front face of the front housing must be clean.
- Position the gasket and front cover (3) on the engine.
- Install bolts (1).
- Install bolts (2). Remove the support from the attachment for the accessory drive.
Show/hide table
|
| |
| Illustration 2 | g01173620 |
End By:
- Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Install".
- Install the fan drive, if necessary. Refer to Disassembly and Assembly, "Fan Drive - Install".
- Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
Caterpillar Information System:
3176C, 3406E and 3456 Industrial Engines Engine Overspeeds
C4.4 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
3176C, 3406E and 3456 Industrial Engines Coolant Level - Test
C13, C15, and C18 Tier 4 Final Engines Air Lines
3176C, 3406E and 3456 Industrial Engines Indicator Lamp - Test
3176C, 3406E and 3456 Industrial Engines Electronic Service Tool Does Not Communicate
C9 Petroleum Engines Flywheel Housing - Remove and Install
C15 and C18 Petroleum Generator Sets Overhaul (Top End)
C15 and C18 Petroleum Generator Sets Overhaul (Major)
C9 Petroleum Engines Flywheel - Remove and Install
C18 Petroleum Generator Sets Fuel System - Prime
C15 and C18 Petroleum Generator Sets Fuel System - Prime
3176C, 3406E and 3456 Industrial Engines Diagnostic Code Cross Reference
C18 Petroleum Generator Sets Instrument Panel - Inspect
C27 and C32 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Parallel Setpoint Viewing OP2-3
C9 Petroleum Engines Gear Group (Front) - Remove
C9 Petroleum Engines Gear Group (Front) - Install
2007/11/26 Improved PL1000E Hardware and Software is Now Available {7610}
3516B Engine for 994F and 994H Wheel Loaders Coolant Contains Oil
3176C, 3406E and 3456 Industrial Engines ECM Does Not Communicate with Other Modules
G3520B Industrial Engines Event Codes
G3520B Industrial Engines Diagnostic Trouble Codes
C4.4 Generator Set Engines Injector Data Incorrect - Test