- Track-Type Tractor
- D8T (S/N: FMC1-810)
- D9T (S/N: REX1-496)
Description Of Change: The NOx Reduction System (NRS) cooler group has a more robust design and the water lines group is more flexible.
Adaptable To: The following changes are adaptable to the products within the listed serial numbers, and are effective with all products after the listed serial numbers.
Required Parts
Part Number | Part Description | Qty |
---|---|---|
Bolt | 6 | |
Bolt | 1 | |
Cooler As | 1 | |
Hard Washer | 7 | |
Mounting Bracket | 1 | |
Clamp As | 4 |
Water Lines Gp | ||
---|---|---|
Part Number | Part Description | Qty |
Bolt | 2 | |
Bolt | 1 | |
Bolt | 1 | |
Hard Washer | 1 | |
Bolt | 2 | |
Hard Washer | 2 | |
Tube As | 1 | |
Tube As | 1 | |
Bracket As | 1 | |
Hose | 1 | |
Band Clamp | 2 | |
O-Ring Seal | 2 | |
Clip | 1 | |
Clip | 1 |
Miscellaneous Parts | ||
---|---|---|
Part Number | Part Description | Qty |
Bellows As | 1 | |
Bracket As | 1 | |
Bolt | 2 | |
O-Ring Seal | 1 | |
Clamp | 3 |
Installation Procedure
Illustration 1 | g06207090 |
Current EGR cooler set-up. |
- Drain the coolant into a suitable container for reuse or disposal.
Show/hide table
Illustration 2 g06207113 (1) Coolant Outlet
(2) Coolant Inlet - Remove and retain the clips and retainers as shown in Illustration 2 for reuse.
- Remove water lines (1) and (2) (outlet and inlet from cooler).
Show/hide table
Illustration 3 g06207093 (1) 9N-5085 Clamp - Remove and discard the two band clamps.
Show/hide table
Illustration 4 g06207326 (4) 344-2636 Clamp As - Remove the (4) clamps on EGR cooler.
Show/hide table
Illustration 5 g06207336 (5) 362-6634 Bracket As - Remove the edge plate (5) from the EGR cooler.
Show/hide table
Illustration 6 g06207351 (6) 436-9146 Exhaust Cooler and Mounting Gp (NRS) - Remove the EGR cooler (6).
Show/hide table
Illustration 7 g06207356 (7) 0S-1608 Bolt
(8)5M-2894 Hard Washer
(9)0L-2070 Bolt
(10)355-8321 Mounting Bracket - Remove the bolts (7) and (9) along with the washers (8).
- Remove the bracket (10).
Show/hide table
Illustration 8 g06207641 Updated with new EGR cooler Show/hide tableIllustration 9 g06207665 (8) 5M-2894 Hard Washer
(9)0L-2070 Bolt
(11)0L-1352 Bolt
(12)509-7456 Mounting Bracket - Install the EGR Bracket (12) with bolts (11), washers (8). Install bolt (9) and washer 8.
Tighten bolts to ...
47 ± 9 N·m (34.6 ± 6.6 lb ft) Show/hide tableIllustration 10 g06207713 (13) 449-3065 Cooler As - Install the new EGR cooler (13).
Show/hide table
Illustration 11 g06207729 Edge bracket assembly
(14)493-1489 Bracket As - Install the bracket assembly (14).
Show/hide table
Illustration 12 g06208498 (15) 510-3002 Clamp As - Install the EGR clamp and secure the cooler to the bracket.
Tightening Procedure
Tighten bolts of each clamp assembly in sequence 3, 2, 1, 4 with below steps.
1. Tighten bolts indicated (Z) to
20 ± 5 N·m (14.7 ± 3.7 lb ft) 2. Tighten bolts indicated (X) to
20 ± 5 N·m (14.7 ± 3.7 lb ft) 3. Retighten bolts indicated (Z) to
40 ± 5 N·m (29.5 ± 3.7 lb ft) 4. Retighten bolts indicated (X) to
40 ± 5 N·m (29.5 ± 3.7 lb ft) Show/hide tableIllustration 13 g06208709 (16) 493-0357 Tube As
(17)8S-0023 Clip
(18)8S-0024 Clip
(19)0S-1594 Bolt
(20)9X-6458 Hard Washer
(21)0S-0509 Bolt
(22)5M-2894 Hard Washer
(23)338-1556 Retainer
(24)7L-6580 O-Ring Seal
(25)493-0358 Tube As
(26) Tube As
(27)8T-9588 O-Ring Seal
(28)4F-7957 Bolt
(29)5P-0537 Hard Washer
(30)445-6881 Hose
(31)523-4273 Band Clamp - Lubricate the bore lightly while installing the O-Ring (24) to tube and attach the tube (16) to the EGR.
- Secure the tube with one bolts (21), one washer (22), and one retainer (23).
Tighten the bolt to ...
47 ± 9 N·m (35 ± 6.6 lb ft) Note: The retainer flange needs to be facing out on the cooler outlet.
- Attach the water lines with clamps (17) and (18) with two bolts (19) and two washers (20).
Note: The clips are placed in two different places.
Tighten both bolts ...
47 ± 9 N·m (35 ± 6.6 lb ft) - Attach tube (16) with a hose (29) and secure the hose clamps (30).
Tighten both hose clamps to ...
7 ± 1 N·m (5 ± 0.7 lb ft) - Attach tube (25) with a hose (30) and secure the hose clamps (31).
- Lubricate the bore lightly while installing the O-Ring (24) to tube (25) and attach the tube (25) to the engine.
- Secure the tube with one bolts (21), one washer (22), and one retainer (23).
Tighten the bolt to ...
47 ± 9 N·m (35 ± 6.6 lb ft) - Lubricate the bore lightly while installing the O-Ring (27) to tube (26) and attach the tube to the EGR.
- Secure the tube with two bolts (28), two washers (29).
Tighten both bolts ...
12 ± 3 N·m (8.8 ± 2.2 lb ft) Show/hide tableIllustration 14 g06209165 Lines group turbo oil - Refer to Illustration 14 for the placement of the new 509-7456 Mounting Bracket and p-clip.
- Refill the radiator and engine with coolant. Refer to Special Instruction , M0070968, "Coolant Drain and Vacuum Fill Procedure For Certain C9.3 Through C18 Tier 4 Engines" for proper coolant fill procedure.
Show/hide table
Illustration 15 g06219274 (32) Use existing Clip and Washer
(33)8T-4136 Bolt
(34)498-0954 Bracket AsNote: This step is only for D8T machines.
- Install bracket (34) along with the existing clip and washer. Secure with bolt (33).
Heat Shield Rework (Where Applicable)
- Remove heat shield.
Show/hide table
Illustration 18 g06211201 Before and after illustration. The green is the new shield and compared to the red of the old shield. Show/hide tableIllustration 19 g06212210 (A) 34 mm (1.3 inch)
(B) R17
(C)24 mm (0.9 inch)
(D)43 mm (1.6 inch) - Cut out the area in red as shown in Illustration 18.
Show/hide table
Illustration 20 g06211209 - Illustration of the new and old water lines looks like after cutting out the heat shield.
Show/hide table
Illustration 21 g06211213 Side view of the heat shield - Relocate the spring/hook from current location (1) to new location (2).
Show/hide table
Illustration 22 g06211216 Bottom view of the heat shield - Relocate the Spring/Hook to current location (3) to new location (4).
Illustration 16 | g06211161 |
Old shield group |
Illustration 17 | g06211164 |
Old water lines gp |