Axle Shaft - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Guide bolts M16 − 2 mm by 2 inch |
2 |
| B | 138-7575 | Link Brackets | 3 |
| C | 1U-8848 | Axle Shaft Installation Handle | 1 |
| 447-6595 | Adapter | 1 | |
Start By:
- Drain the final drive oil into a suitable container for storage or disposal.
Show/hide table
| |
| Illustration 1 | g06118508 |
Show/hide table
| |
| Illustration 2 | g06118514 |
Show/hide table
| |
| Illustration 3 | g06118523 |
Show/hide table
| |
| Illustration 4 | g06118532 |
Show/hide table
| |
| Illustration 5 | g06118541 |
Show/hide table
| |
| Illustration 6 | g06118548 |
Show/hide table
| |
| Illustration 7 | g06118555 |
Show/hide table
| |
| Illustration 8 | g06118557 |
Show/hide table
| |
| Illustration 9 | g06118560 |
- Install the axle shaft in the reverse order of removal.
- Install new bolts (3.2) and (2.2). Tighten bolts to a torque of
145 ± 30 N·m (106 ± 22 lb ft) . Then, turn bolts an additional 60° ± 5°.
- Install new bolts (3.2) and (2.2). Tighten bolts to a torque of
Caterpillar Information System:
994K Wheel Loader Power Train Gear Motor (Axle Oil Cooler Fan) - Remove and Install
340F Excavator Machine Systems Travel Motor Lines
854K Wheel Dozer Monitoring System
374F Excavator Fuel Transfer Pump (Refueling) - If Equipped
D11T Track-Type Tractor Undercarriage - Clean
A New Procedure To Route Wire Harness Under Right-Hand And Left-Hand Console Covers On Certain D6T Track-Type Tractors {1408, 7329} A New Procedure To Route Wire Harness Under Right-Hand And Left-Hand Console Covers On Certain D6T Track-Type Tractors {1408, 7329}
340F Excavator Machine Systems Stick Lines
980L Medium Wheel Loaders Sensor Signal (Analog, Active) - Test
980L Medium Wheel Loaders Relay - Test
994K Wheel Loader Power Train Access Doors/Covers - Remove and Install - Ladders and Walkway
980L Medium Wheel Loaders Parameter - Test
340F Excavator Machine Systems Stick Cylinder Lines
MD6250 Rotary Drill Systems Operational Checks (Hydraulic System)
980L Medium Wheel Loaders Sensor Signal (Analog, Passive) - Test
980L Medium Wheel Loaders Sensor Signal (PWM) - Test
994K Wheel Loader Power Train Axle Oil Cooler - Remove and Install
D6T Track Type Tractor Power Train Steering Differential and Brake - Disassemble
980L Medium Wheel Loaders Sensor Supply - Test
950 GC Wheel Loader Braking and Hydraulic Fan System Control Manifold (Charging Valve for the Brake Accumulators) - Test and Adjust
950 GC Wheel Loader Braking and Hydraulic Fan System Service Brake System Pressure - Test
950 GC Wheel Loader Braking and Hydraulic Fan System Limit Switch (Stop Light) - Adjust
D6T Track Type Tractor Power Train Steering Differential and Brake - Assemble
950 GC Wheel Loader Braking and Hydraulic Fan System Brake System Air - Purge
Improved Connecting Rod Bolts Are Now Used on Certain C11 and C13 Machine Engines {1225} Improved Connecting Rod Bolts Are Now Used on Certain C11 and C13 Machine Engines {1225}