A New Procedure To Route Wire Harness Under Right-Hand And Left-Hand Console Covers On Certain D6T Track-Type Tractors {1408, 7329}
- Track-Type Tractor
- D6T (S/N: CR31-120; CG81-105; SGA1-103; RAD1-1008; STE1-118; MEL1-205; WRN1-572; KMR1-604; WES1-399; SGT1-434; TMY1-364; HTZ1-657)
Description Of Change:
Show/hide table
| |
| Illustration 1 | g06115636 |
|
Left-Hand Console Cover | |
Show/hide table
| |
| Illustration 2 | g06115640 |
|
Right-Hand Console Cover | |
A new procedure for routing of the wire harness for the console covers has been improved. The wire harness is improved by removing the wire braiding, retape the wire harness, and covered with convoluted tubing for insulation. This braiding removal reduces undue stress on the console cover where the harness comes through the console cover. See Illustration 1 and 2 for the location of improvement.
Adaptable To: The following changes are adaptable to the products within the listed serial numbers, and are effective with all products after the listed serial numbers.
Routing Procedure
- Remove 390-3841 Console As (RH) and 390-3846 Console (LH).
- Reposition the harness to ensure that the harness is routed along side of the weld link and not on top of the weld link. Ensure that the harness lays flat and does not apply any upward pressure on the console cover.
- Ensure the head of the tie-strap is away from the console cover.
Show/hide table
Illustration 5 g06115687 Show/hide table
Illustration 6 g06115689 - Remove the braiding from the wire harness and tape the section that comes through the console cover.
- Reinstall the two console covers.
Show/hide table
| |
| Illustration 3 | g06115647 |
| (A) Right-Hand Console Cover | |
Show/hide table
| |
| Illustration 4 | g06115652 |
| (B) Left-Hand Console Cover | |
Caterpillar Information System:
340F Excavator Machine Systems Stick Lines
980L Medium Wheel Loaders Sensor Signal (Analog, Active) - Test
980L Medium Wheel Loaders Relay - Test
994K Wheel Loader Power Train Access Doors/Covers - Remove and Install - Ladders and Walkway
980L Medium Wheel Loaders Parameter - Test
340F Excavator Machine Systems Stick Cylinder Lines
C9.3 Tier 4 Final Engines Diesel Exhaust Fluid Lines
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Electrical Power Supply - Test
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Data Link - Test
D6T Track Type Tractor Power Train Final Drive - Assemble
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Engine Has Mechanical Noise (Knock)
910M, 914M and 918M Wheel Loader Power Train Gear Motor - Assemble
D11T Track-Type Tractor Undercarriage - Clean
374F Excavator Fuel Transfer Pump (Refueling) - If Equipped
854K Wheel Dozer Monitoring System
340F Excavator Machine Systems Travel Motor Lines
994K Wheel Loader Power Train Gear Motor (Axle Oil Cooler Fan) - Remove and Install
994K Wheel Loader Power Train Axle Shaft - Remove and Install
MD6250 Rotary Drill Systems Operational Checks (Hydraulic System)
980L Medium Wheel Loaders Sensor Signal (Analog, Passive) - Test
980L Medium Wheel Loaders Sensor Signal (PWM) - Test
994K Wheel Loader Power Train Axle Oil Cooler - Remove and Install
D6T Track Type Tractor Power Train Steering Differential and Brake - Disassemble
980L Medium Wheel Loaders Sensor Supply - Test