Cylinder Head - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 4 |
B | - | Clean Engine Oil | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Repeat the procedure for each cylinder head.
- Clean the surface of the cylinder head and the surface of the spacer plate. A new spacer plate gasket must be installed when the cylinder head is removed.
Show/hide table
Illustration 1 g00760395 - Install O-ring seal (19) on the dowel.
Show/hide table
NOTICE Ensure that the surface of the spacer plate gasket and the surface of the cylinder block are clean. Do not use a gasket adhesive on these surfaces.
- Install a new spacer plate gasket (18) on the dowels in the cylinder block.
Show/hide table
Illustration 2 g00760369 - Install spacer plate (17) on the dowels.
- Install four new seals (13) and (14) in spacer plate (17).
- Install new O-ring seal (15) on the dowel.
- Install cylinder head gasket (16).
Show/hide table
Illustration 3 g00585054 Show/hide tableNOTICE The plug at Location (A) MUST be installed on engines that are equipped with a dry exhaust manifold. REMOVE the plug on engines that are equipped with a water cooled exhaust manifold.
Show/hide tableIllustration 4 g00760306 - Install Tooling (A) and attach a suitable lifting device to the cylinder head. Position cylinder head (11) on the spacer plate. Remove Tool (A).
- Install bolts (10) and bolts (12) in the cylinder head.
Show/hide table
Illustration 5 g00585055 - Use the following procedure to tighten the cylinder head bolts.
- Apply Tooling (B) to the threads of the cylinder head bolts.
- Tighten bolt (1) through bolt (8) in a numerical sequence to a torque of
30 ± 5 N·m (22 ± 4 lb ft) . - Tighten bolt (1) through bolt (8) again in a numerical sequence to a torque of
270 ± 35 N·m (200 ± 26 lb ft) . - Tighten bolt (1) through bolt (8) again in a numerical sequence to a torque of
450 ± 20 N·m (330 ± 15 lb ft) . - Tighten bolt (9) and bolt (10) to a torque of
55 ± 10 N·m (40 ± 7 lb ft) .
Show/hide tableIllustration 6 g00760271 - Install gasket (8) and exhaust elbow (9).
Show/hide table
Illustration 7 g00760018 - Install new gaskets (6) and tube (4) that runs from the water manifold to the cylinder head.
- Install new gasket (7) and air inlet elbow (5).
Show/hide table
Illustration 8 g00760142 - Install exhaust temperature sensor (3) in the cylinder head.
Show/hide table
Illustration 9 g00759319 - Install valve cover base (2) on the cylinder head .
- Install bracket (1) on the water manifold.
- Fill the cooling system to the correct level with coolant. Refer to the Operation and Maintenance Manual for the correct filling procedure.
End By:
- Install the rocker shaft assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Push Rods - Install".
Caterpillar Information System:
G3516B and G3520B Generator Set Engines Cylinder Head - Assemble
G3516B and G3520B Generator Set Engines Cylinder Head - Remove
G3516B and G3520B Generator Set Engines Cylinder Head - Disassemble
G3516B and G3520B Generator Set Engines Rocker Shaft and Push Rod - Install
C18 Power Module Cooling System Coolant (ELC) - Change
G3516B and G3520B Generator Set Engines Rocker Shaft and Push Rod - Remove
The Filter Bypass Light for the Transmission Filter May Activate Prematurely{3103} The Filter Bypass Light for the Transmission Filter May Activate Prematurely{3103}
G3516 Petroleum Engines Accessory Drive (Front) - Install
3508C, 3512C and 3516C Marine Engines Turbocharger - Remove
2007/04/09 An Improved Expansion Tank is Available {1379}
G3516 Petroleum Engines Accessory Drive (Front) - Remove
TH48-E70-C27I, TH48-E70-C32I and TH48-E70-C32P Petroleum Power Train packages and TH48-E70 Petroleum Transmission Power Train Electronic Control System Normal Operation
G3516B and G3520B Generator Set Engines Piston and Connecting Rods - Remove
Procedure for Properly Timing the Air Compressor and the Fuel Injection Pump on C7 Engines{1251, 1803} Procedure for Properly Timing the Air Compressor and the Fuel Injection Pump on C7 Engines{1251, 1803}
Procedure to Torque the Camshaft Gear{1210, 1212} Procedure to Torque the Camshaft Gear{1210, 1212}
C7 and C9 On-highway Engines ARD Nozzle - Clean
2007/03/12 Improved Camshaft Lifters are Available {1209, 1290}
2007/02/26 Improved Jacket Water Heaters Are Now Available {1383}
G3516B and G3520B Generator Set Engines Piston and Connecting Rods - Install
G3516B and G3520B Generator Set Engines Cylinder Liner - Remove
G3516B and G3520B Generator Set Engines Cylinder Liner - Install
G3516B and G3520B Generator Set Engines Camshaft Bearings - Remove
G3516B and G3520B Generator Set Engines Crankshaft - Remove
G3516B and G3520B Generator Set Engines Crankshaft - Install