G3516B and G3520B Generator Set Engines Caterpillar

Installation Procedure

Show/hide table

Illustration 1	g00577390

1. If crankshaft gears (6) were removed, install crankshaft gears (6) on the crankshaft and install bolts (7).

2. Check the clearance of the bearings. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure.
   Show/hide table

   Illustration 2	g01353563

   Note: Place clean engine oil on the main bearings and on the connecting rod bearings prior to installation.

   Note: The upper halves of the main bearings have an oil hole in the center.

3. Install the upper halves of main bearings (8) in the cylinder block.

4. Install the upper halves of connecting rod bearings (9) in the connecting rod assemblies.
   Show/hide table

   Illustration 3	g01353615
   Typical example

   Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.

5. Attach a suitable lifting device to crankshaft (4) and position the crankshaft in the cylinder block. The weight of crankshaft (4) is approximately 762 kg (1680 lb).
   Show/hide table

   Illustration 4	g01353620
   Tightening sequence

   Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.

6. Place Tooling (C) on the bolts for the main bearing caps.
   Show/hide table

   Illustration 5	g01353682

7. Place clean engine oil on thrust plates (3). Install thrust plates (3) on each side of the center main bearing.

8. Place main bearing caps (5) into position and install the bolts. Tighten the bolts in the numerical sequence that is shown above to a torque of 190 ± 14 N·m (140 ± 10 lb ft). Tighten the bolts again for an additional 180 ± 5 degrees.

9. Check the end play with Tooling (B). The end play must not exceed 0.40 ± 0.23 mm (0.0157 ± 0.0091 inch).
   Show/hide table

   Illustration 6	g01353696

10. Position the connecting rods on the journals of the crankshaft. Install connecting rod bearing caps (2).

    Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod.

    Show/hide table

    Illustration 7	g01353701
    Tightening sequence

11. Place Tooling (C) on the bolts for the connecting rod caps and install the bolts.

12. Tighten the bolts with the following steps:

    1. Tighten bolts (14) and (15) to a torque of 90 ± 5 N·m (65 ± 4 lb ft).

    2. Tighten bolts (16) and (17) to a torque of 90 ± 5 N·m (65 ± 4 lb ft).

    3. Tighten bolts (14) and (15) again to a torque of 90 ± 5 N·m (65 ± 4 lb ft).

    4. Tighten bolts (16) and (17) again to a torque of 90 ± 5 N·m (65 ± 4 lb ft).

    5. Tighten each bolt for an additional 90 ± 5 degrees (1/4 turn). An impact wrench may be used.

13. Place the remaining connecting rod caps in position and tighten the bolts with the same procedure that is in Steps 12a through 12e.
    Show/hide table

    Illustration 8	g01353745

    Show/hide table

    NOTICE
    Each counterweight is numbered and must be installed in the same position as the corresponding number on the crankshaft mounting pad in order to prevent damage to the crankshaft.

14. Install counterweights (1).

15. The following procedure is for the installation of the counterweights inG3516 Engines.

    1. Ensure that the dowels are in the correct position and install the counterweights on the crankshaft.

    2. Apply Tooling (C) to the threads of the bolt, to the shank of the bolt, and to the seat of the bolt prior to assembly.

    3. Tighten the bolts in all of the counterweights to a torque of 70 ± 5 N·m (50 ± 4 lb ft).

    4. Tighten the bolts in all of the counterweights for an additional 120 ± 5 degrees (1/3 turn).

16. Use Tooling (A) to rotate the engine back to a vertical position.

Note: Refer to the Specifications Module for more information on the crankshaft.

End By:

1. Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".

2. Install the balancer gear on the rear gear group. Refer to Disassembly and Assembly, "Gear Group (Rear) - Install".

3. Install the front drive housing. Refer to Disassembly and Assembly, "Front Drive Housing - Install".

4. Install the rocker shaft assemblies and the pushrods. Refer to Disassembly and Assembly, "Rock Shaft and Push Rods - Install".