Cylinder Liner - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 5P-8665 | Cylinder Liner Puller | 1 |
| B | 6V-4133 | Wedge Bracket | 1 |
Start By:
- Remove the pistons and the connecting rod assemblies. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a suitable container for storage or disposal.
- Place a cover on the crankshaft journals in order to shield the journals from dirt and coolant.
- Install Tooling (A) and (B) in order to remove the cylinder liner.
Show/hide table
Illustration 2 g00578731 Typical example - Remove seals (1) and filler band (2) from the cylinder liner.
Show/hide table
| |
| Illustration 1 | g00578729 |
|
Typical example | |
Caterpillar Information System:
G3516B and G3520B Generator Set Engines Piston and Connecting Rods - Install
2007/02/26 Improved Jacket Water Heaters Are Now Available {1383}
2007/03/12 Improved Camshaft Lifters are Available {1209, 1290}
C7 and C9 On-highway Engines ARD Nozzle - Clean
Procedure to Torque the Camshaft Gear{1210, 1212} Procedure to Torque the Camshaft Gear{1210, 1212}
Procedure for Properly Timing the Air Compressor and the Fuel Injection Pump on C7 Engines{1251, 1803} Procedure for Properly Timing the Air Compressor and the Fuel Injection Pump on C7 Engines{1251, 1803}
G3516B and G3520B Generator Set Engines Piston and Connecting Rods - Remove
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Cylinder Head - Install
G3516B and G3520B Generator Set Engines Cylinder Head - Assemble
G3516B and G3520B Generator Set Engines Cylinder Head - Remove
G3516B and G3520B Generator Set Engines Cylinder Head - Disassemble
G3516B and G3520B Generator Set Engines Rocker Shaft and Push Rod - Install
G3516B and G3520B Generator Set Engines Cylinder Liner - Install
G3516B and G3520B Generator Set Engines Camshaft Bearings - Remove
G3516B and G3520B Generator Set Engines Crankshaft - Remove
G3516B and G3520B Generator Set Engines Crankshaft - Install
C18 Marine Auxiliary and Marine Generator Set Engines Diagnostic Trouble Codes
C18 Marine Auxiliary and Marine Generator Set Engines Event Codes
G3408 and G3412 Engines Gas Engine Ignition
CX35 On-Highway Transmission General Troubleshooting Information
C18 Marine Engines Component Location
320D, 320D2, 324D, 325D, 329D, 330D and 336D Excavators Long Reach Front Overload Warning - Set - If Equipped
C18 Marine Auxiliary Engine Model View Illustrations
CX35 On-Highway Transmission Oil Filter (Transmission)