A New Torque Specification For the Cap Nuts on Fuel Injectors is Now Used {1120, 1290, 1408}
- Generator Set:
- C27 GEN SET (S/N: DWB1-UP; STR1-UP)
- Industrial Engine:
- C27 INDUSTRIAL (S/N: TWM1-UP)
- Marine Engine:
- C32 MARINE (S/N: RNC1-UP)
- Petroleum Engine:
- C32 PETROLEUM (S/N: SMP1-UP)
- Power Module:
- C32 POWER MODUL (S/N: MEG1-UP)
- C32 GEN SET (S/N: SXC1-UP; WDR1-UP)
- C32 INDUSTRIAL (S/N: TLD1-UP)
Description of Change: A new torque specification is now used on C27 and C32 engines. The new torque specification is for the cap nuts on the fuel injector. The new torque specification will better secure the wiring harness to the fuel injector.
Adaptable To: The old torque specification for the cap nuts was 1.7 ± 0.25 N·m (15 ± 2 lb in). The new torque specification is 2.5 ± 0.25 N·m (22 ± 2 lb in). The new torque specification is adaptable to all the above serial numbers.
Caterpillar Information System:
CX31 On-Highway Transmission Power Train Pump Drive - Remove - Rear PTO Shaft
2007/10/01 Correct Installation Procedure for the 235-1448 Tube As {1304, 1306}
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Actuator (Air Conditioner Control)
2006/09/11 A New Clamp for the Air Cleaner is Used {1051}
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Solenoid and Relief Valve (Output Transfer Gears) - Drop Box) (12 Volt
C0.5, C0.7, C1.1, C1.5, C1.6 and C2.2 Industrial Engines Fuel System - Prime
C280-12 and C280–16 Marine Engines Cylinder Head - Remove
3516C Locomotive Engine Speed Sensor - Clean/Inspect
3500 Engines Fumes Disposal System
3516C Locomotive Engine Engine Air Cleaner Service Indicator - Inspect
3516C Locomotive Engine Starting Motor - Inspect
2006/08/21 A Improved Alternator Guard in Used {7174}
2006/10/23 Improved Head Gasket {1100, 1124}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys 4 Wire Out Voltage - Calibrate
C175-16 Locomotive Engine ECM - Replace
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys In Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys AC Output Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys 4 Wire Output Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Voltage - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Load Cell - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Field Coil Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Current - Calibrate
C280-12 and C280–16 Marine Engines Cylinder Head - Install
C11 and C13 Engines and 14M and 16M Motor Graders Electronic Service Tool Does Not Communicate