Correct Installation Procedure for the 235-1448 Tube As {1304, 1306}
- Engine:
- C11 (S/N: KCA1-UP)
- C13 (S/N: KCB1-UP)
Oil leaks may occur if the 235-1448 Tube As is not properly aligned. Use the following procedure in order to install the 235-1448 Tube As .
- First, install the 235-1448 Tube As into the oil filter base. This will allow the correct alignment of the 235-1448 Tube As to the bore in the oil filter base.
Note: A slight adjustment to the position of the oil filter base may be necessary in order to achieve correct alignment of the tube.
- Next, tighten the bolts at the base of the 235-1448 Tube As. Tighten the bolts to 28 ± 7 N·m (21 ± 5 lb ft).
Show/hide table
Illustration 1 | g01422829 |
Location of the 235-1448 Tube As |
Caterpillar Information System:
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Actuator (Air Conditioner Control)
2006/09/11 A New Clamp for the Air Cleaner is Used {1051}
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Solenoid and Relief Valve (Output Transfer Gears) - Drop Box) (12 Volt
C0.5, C0.7, C1.1, C1.5, C1.6 and C2.2 Industrial Engines Fuel System - Prime
C280-12 and C280–16 Marine Engines Cylinder Head - Remove
3516C Locomotive Engine Speed Sensor - Clean/Inspect
3500 Engines Fumes Disposal System
3516C Locomotive Engine Engine Air Cleaner Service Indicator - Inspect
3516C Locomotive Engine Starting Motor - Inspect
2006/08/21 A Improved Alternator Guard in Used {7174}
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Service Tools
C280-12 and C280–16 Marine Engines Fuel Injector - Install
CX31 On-Highway Transmission Power Train Pump Drive - Remove - Rear PTO Shaft
2006/09/04 A New Torque Specification For the Cap Nuts on Fuel Injectors is Now Used {1120, 1290, 1408}
2006/10/23 Improved Head Gasket {1100, 1124}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys 4 Wire Out Voltage - Calibrate
C175-16 Locomotive Engine ECM - Replace
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys In Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys AC Output Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys 4 Wire Output Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Voltage - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Load Cell - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Field Coil Current - Calibrate
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Current - Calibrate