Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091} Caterpillar


Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091}

Usage:

D3400 01T
Engine:Commercial All
Engine:Truck All
Generator Set: All
Machine Engines: All
Marine Engine: ALL

Introduction


NOTICE

Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM) are not applicable to all engines. Some engines contain a DPF and a CCM device that were installed as original equipment to meet engine emissions certification requirements. However, some engines may have had the devices installed during a retrofit program for emissions reduction.


Do not perform any procedure in this Special Instruction until you read this information and you understand this information.

Procedure for Shipping the Diesel Particulate Filters (DPF)

------ WARNING! ------

Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.

----------------------

Place all the used Diesel Particulate Filter (DPF) center sections, regardless of condition, into a 0.152 mm (0.006 inch) thick plastic bag. Make sure that the bag is sealed before placing the DPF into a shipping container. This must be performed in order to contain any constituents from the used DPF during shipping. New replacement diesel particulate filters may come with a 0.152 mm (0.006 inch) plastic bag that can be used for wrapping the used DPF.

Procedure for Shipping the Catalytic Converter Mufflers (CCM)

Seal the inlet port and the outlet port on all used Catalytic Converter Mufflers (CCM) with rubber caps or plastic caps. Various sized plastic caps can be ordered from the Cat Shop Supplies and Hand Tools catalog. Reference caps and plugs under the Shop Supplies section. An alternative is to seal the inlet ports and outlet ports with a 0.152 mm (0.006 inch) thick sheet of plastic and 50 mm (2 inch) wide sealing tape with good adhesive properties before shipping. Sealing or capping must be performed in order to contain any constituents from the used CCM during shipping.

Caterpillar Information System:

2008/02/04 Correction to Special Instruction, REHS0248, "Field Assembly of 854G Wheel Dozer" {7000, 7960}
973D Track-Type Loader Engine Supplement Engine Oil Filter, Oil Filter Base and Oil Cooler - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train Electronic Control Module (ECM) - Flash Program
C27 and C32 Engines for Caterpillar Built Machines Switch Circuits - Test
993K Wheel Loader Power Train Electronic Control Module (ECM) - Configure
993K Wheel Loader Power Train Electronic Control Module (ECM) - Replace
993K Wheel Loader Power Train Reduced Rimpull Setting (Electronic Technician) - Adjust
993K Wheel Loader Power Train Reduced Rimpull Setting (Operator Monitor) - Adjust
Replacement of the Electrohydraulic Control Group on the 834G Wheel Dozer{5702, 5705} Replacement of the Electrohydraulic Control Group on the 834G Wheel Dozer{5702, 5705}
C27 and C32 Engines for Caterpillar Built Machines Compression Brake Solenoid Circuit - Test
C4.4 Industrial Engine Accessory Drive - Install
C4.4 Industrial Engine Accessory Drive - Assemble
973D Track-Type Loader Engine Supplement Engine - Remove
973D Track-Type Loader Engine Supplement Engine - Install
C11 and C13 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
992K Wheel Loader and 854K Wheel Dozer Power Train Duo-Cone Conventional Seals - Install
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Renewal Solenoid Circuit - Test
2008/02/11 New Three Ring Pistons are Now Used In Turbocharged 3204 <B>S/N:</B>45V Engines {1214, 1215}
C27 and C32 Engines for Caterpillar Built Machines E2089 Oil Renewal System Cannot Operate
854K Wheel Dozer Machine Systems Steering Cylinder - Remove and Install
973D Track-Type Loader Machine Systems Cab - Tilt - Full Tilt
2008/03/10 An Improved Fuel Tank Fast Fill Adapter is Now Used {1710}
C27 and C32 Engines for Caterpillar Built Machines CID 0800 FMI 14 VIMS Main Module special instruction
C27 and C32 Engines for Caterpillar Built Machines CID 0800 FMI 09 VIMS Main Module abnormal update rate
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.