Electronic Control Module (ECM) - Configure
Show/hide table
| Required Tools | ||
| Part Number | Description | Quantity |
| JEBD3003 | Caterpillar Electronic Technician (Cat ET) | 1 |
| 171-4401 | Communications Adapter II | 1 |
| 207-6845 | Adapter Cable As | 1 |
| 160-0141 | Adapter Cable As | 1 |
Cat ET is used to access the configuration screen. A message on the screen will give instructions that guide the user through the procedure. Refer to the manual that is provided with the Cat ET software for more information about Cat ET.
The machine electronic control module (ECM) must be configured when the machine ECM has been replaced. The ECM needs to be configured before a calibration can be started.
A check of the configuration screen could resolve a problem with the machine. A problem with a component could be identified as one of the following items:
- The component is not installed.
- The component is installed but a change to the installation is needed in order to correct a problem.
Follow these instructions to get to the configuration screen:
- Connect the communications adapter and the computer to the diagnostic service tool connector.
- Start Cat ET.
Show/hide table
Illustration 1 g01329156 Typical configuration screen - Select "File". Go to "Select ECM". Choose the "Transmission ECM".
- Go to the "Service" Menu. Select "Configuration". Click "OK". Certain operations or characteristics can be changed.
Caterpillar Information System:
993K Wheel Loader Power Train Electronic Control Module (ECM) - Replace
993K Wheel Loader Power Train Reduced Rimpull Setting (Electronic Technician) - Adjust
993K Wheel Loader Power Train Reduced Rimpull Setting (Operator Monitor) - Adjust
Replacement of the Electrohydraulic Control Group on the 834G Wheel Dozer{5702, 5705} Replacement of the Electrohydraulic Control Group on the 834G Wheel Dozer{5702, 5705}
C27 and C32 Engines for Caterpillar Built Machines Compression Brake Solenoid Circuit - Test
C4.4 Industrial Engine Accessory Drive - Install
C4.4 Industrial Engine Accessory Drive - Assemble
C4.4 Industrial Engine Accessory Drive - Disassemble
C4.4 Industrial Engine Accessory Drive - Remove
993K Wheel Loader VIMS Loader Payload System Glossary of Terms
993K Wheel Loader VIMS Loader Payload System VIMSpc Payload Reports
993K Wheel Loader VIMS Loader Payload System VIMSpc Onboard Configuration
C27 and C32 Engines for Caterpillar Built Machines Switch Circuits - Test
854K Wheel Dozer and 992K Wheel Loader Power Train Electronic Control Module (ECM) - Flash Program
973D Track-Type Loader Engine Supplement Engine Oil Filter, Oil Filter Base and Oil Cooler - Remove and Install
2008/02/04 Correction to Special Instruction, REHS0248, "Field Assembly of 854G Wheel Dozer" {7000, 7960}
Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091} Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091}
973D Track-Type Loader Engine Supplement Engine - Remove
973D Track-Type Loader Engine Supplement Engine - Install
C11 and C13 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
992K Wheel Loader and 854K Wheel Dozer Power Train Duo-Cone Conventional Seals - Install
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Renewal Solenoid Circuit - Test
2008/02/11 New Three Ring Pistons are Now Used In Turbocharged 3204 <B>S/N:</B>45V Engines {1214, 1215}
C27 and C32 Engines for Caterpillar Built Machines E2089 Oil Renewal System Cannot Operate