Electronic Control Module (ECM) - Flash Program
Perform the following procedure to flash program the ECM. The ECM is flashed to upgrade the software. Flash programming of the ECM must also be done if the ECM has been replaced. The Cat® Electronic Technician (Cat® ET) contains the program WinFlash. WinFlash is used to load software into the ECM. The following procedure is used to FLASH software into the ECM.
Show/hide table
| |
| Illustration 1 | g03874942 |
|
Connections for the Communication Adapter III and the Cat® Electronic Technician (Cat ET) Service Tool. The components that are needed to use the Communication Adapter III and Cat ET are: (1) Cable (2) 317-7484 Communication Adapter Gp (3) 457-6114 CA3 Ethernet FLASH Cable (4) Current version of Cat ET program software and an IBM-compatible personal computer | |
Note: Plus+1 Service Tool for Caterpillar software will be required in addition to Cat ET software.
Acquire the most recent version of the Cat Electronic Technician (Cat ET) Service Tool. Reference JERD2129.
- Connect the data link cable between the communication adapter and the electronic technician.
- Connect the data link cable between the communication adapter and the diagnostic connector of the machine.
- Turn the disconnect switch and the key start switch to the ON position.
- Ensure that the transmission direction switch is in the neutral position.
- Ensure that the engine is not running.
- Use WinFlash to load the software.
The program will run and display a message when the download is complete.
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Switch Circuits - Test
993K Wheel Loader Power Train Electronic Control Module (ECM) - Configure
993K Wheel Loader Power Train Electronic Control Module (ECM) - Replace
993K Wheel Loader Power Train Reduced Rimpull Setting (Electronic Technician) - Adjust
993K Wheel Loader Power Train Reduced Rimpull Setting (Operator Monitor) - Adjust
Replacement of the Electrohydraulic Control Group on the 834G Wheel Dozer{5702, 5705} Replacement of the Electrohydraulic Control Group on the 834G Wheel Dozer{5702, 5705}
C27 and C32 Engines for Caterpillar Built Machines Compression Brake Solenoid Circuit - Test
C4.4 Industrial Engine Accessory Drive - Install
C4.4 Industrial Engine Accessory Drive - Assemble
C4.4 Industrial Engine Accessory Drive - Disassemble
C4.4 Industrial Engine Accessory Drive - Remove
993K Wheel Loader VIMS Loader Payload System Glossary of Terms
973D Track-Type Loader Engine Supplement Engine Oil Filter, Oil Filter Base and Oil Cooler - Remove and Install
2008/02/04 Correction to Special Instruction, REHS0248, "Field Assembly of 854G Wheel Dozer" {7000, 7960}
Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091} Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091}
973D Track-Type Loader Engine Supplement Engine - Remove
973D Track-Type Loader Engine Supplement Engine - Install
C11 and C13 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
992K Wheel Loader and 854K Wheel Dozer Power Train Duo-Cone Conventional Seals - Install
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Renewal Solenoid Circuit - Test
2008/02/11 New Three Ring Pistons are Now Used In Turbocharged 3204 <B>S/N:</B>45V Engines {1214, 1215}
C27 and C32 Engines for Caterpillar Built Machines E2089 Oil Renewal System Cannot Operate
854K Wheel Dozer Machine Systems Steering Cylinder - Remove and Install
973D Track-Type Loader Machine Systems Cab - Tilt - Full Tilt