Torque Converter
Show/hide table
图 1 | g02632199 |
Show/hide table
121-0029 变矩器总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 6     | 0S-1588 螺栓     | 拧紧至扭矩为 50 ± 7 N·m (37 ± 5 lb ft)。     |
2     | 10     | 7B-3235 螺栓     | 拧紧至扭矩为 120 ± 15 N·m (89 ± 11 lb ft)。     |
3     | 12     | 1B-2886 螺栓     | 拧紧至扭矩为 120 ± 15 N·m (89 ± 11 lb ft)。     |
A     | -     | -     | 导轮与泵轮之间的间隙:     |
新部件直径方向上的间隙(径向间隙)为 0.82 ± 0.50 mm (0.032 ± 0.020 in)。 |
|||
最大允许径向间隙为 1.80 mm (0.071 in)。 |
|||
B     | -     | -     | 导轮与涡轮之间的间隙:     |
新部件直径方向上的间隙(径向间隙)为 1.25 ± 0.26 mm (0.049 ± 0.010 in)。 |
|||
最大允许径向间隙为 1.81 mm (0.071 in)。 |
|||
4     | 20     | 0S-1585 螺栓     | 拧紧至扭矩为 120 ± 15 N·m (89 ± 11 lb ft)。     |
5     | 6     | 0S-1594 螺栓     | 拧紧至扭矩为 50 ± 7 N·m (37 ± 5 lb ft)。     |
6     | 1     | 1D-4585 螺栓     | 拧紧至扭矩为 240 ± 25 N·m (177 ± 18 lb ft)。     |
7     | 2     | 6P-8319 衬套     | 安装后衬套的孔径为 72.878 ± 0.065 mm (2.8692 ± 0.0026 in)。     |
安装深度 (C) 为 19.0 ± 0.5 mm (0.75 ± 0.02 in)。 |
|||
安装深度 (D) 为 28.0 ± 0.5 mm (1.10 ± 0.02 in)。 |
|||
E     | 1     | 294-3365 输出轴     | 新轴位于衬套区域中的直径为 72.726 ± 0.015 mm (2.8632 ± 0.0006 in)。     |
F     | -     | -     | 新盘与耐磨套筒之间的间隙(未调整)为 0.65 ± 0.44 mm (0.026 ± 0.017 in)。     |
为了检查间隙,需要提升变矩器并用支架 (8) 固定住变矩器。 | |||
9     | 24     | 1A-1460 螺栓     | 拧紧至扭矩为 135 ± 15 N·m (100 ± 11 lb ft)。     |
10     | 1     | 1T-0229 轴承锁紧螺母     | 拧紧至扭矩为 985 ± 35 N·m (726 ± 26 lb ft)。     |
在拧紧螺母前,用机油润滑锁定板的表面以及螺纹。 |
Show/hide table
图 2 | g02676157 |
Show/hide table
6P-8317 传动法兰组件 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
H     | 2     | 8M-3405 定位销     | 安装深度为 13.5 ± 0.5 mm (0.53 ± 0.02 in)。     |
Caterpillar Information System:
3306C Engines for Caterpillar Built Machines Fuel Injection Pump
906H, 906H2, 907H, 907H2, 908H and 908H2 Compact Wheel Loaders Monitoring System System Schematic
D11R Track-Type Tractor Power Train Transmission and Torque Converter Pump
2007/07/30 A New Procedure for Adding the Third Valve Improves the Installation for the Shuttle Valve and Seals {5051, 5059, 5063}
C6.6 Engines For Caterpillar Built Machines Customer Specified Parameters Worksheet
924H, 924Hz, 928Hz and 930H Wheel Loaders Machine Systems Refrigerant Accumulator - Remove and Install
C6.6 Engines For Caterpillar Built Machines Customer Specified Parameters Table
2007/07/30 New Wiper Seals Are Now Used in the Oscillating Axle Trunnion Supports {3268, 3278}
2007/07/23 A New Sprocket Segment Improves The Retention Of The Segment {4155, 4184}
924H, 924HZ, 928HZ and 930H Wheel Loaders Power Train Parking Brake - Remove and Install
C6.6 Engines For Caterpillar Built Machines Customer Specified Parameters
928Hz Wheel Loader Hydraulic System General Information
3306C Engines for Caterpillar Built Machines Fuel Injection Pump Housing
D11T Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet)
2010/12/08 The Main Control Valve Is Updated on Certain Wheel Tractor-Scrapers {5051, 5304}
906H, 906H2, 907H, 907H2, 908H and 908H2 Compact Wheel Loaders Monitoring System Self Test
2007/10/22 277-2362 Transmission Analyzer III Group Offers Upgraded Diagnostic Capabilities {0769, 0779, 0783}
906H, 906H2, 907H, 907H2, 908H and 908H2 Compact Wheel Loaders Monitoring System Connector Contact Description
Bench Test Procedure For A D8R Track-Type Tractor Torque Converter{3101} Bench Test Procedure For A D8R Track-Type Tractor Torque Converter{3101}
D3K, D4K and D5K Track-Type Tractors Fuel Tank Cap - Clean
2007/08/06 The Fender Group is Updated {7252}
Valve Bridges are Included with Cylinder Heads{1102, 1123} Valve Bridges are Included with Cylinder Heads{1102, 1123}
2007/07/30 Correction to Systems Operation Testing and Adjusting , "Transmission Hydraulic Control Clutch Pressure - Test" {3167}
C6.6 Engines For Caterpillar Built Machines Can Not Reach Top Engine RPM