Engine Oil Pressure Switch - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
注: 发动机机油压力开关可能位于气门机构盖或缸体中。 有关正确位置,请参阅技术规格, "发动机机油压力开关"。
- 从发动机机油压力开关 (1) 上断开线束组件(未显示)。
- 如果发动机机油压力开关 (1) 位于气门机构盖上,从气门机构盖上拆下发动机机油压力开关。
Show/hide table
图 2 g01307450 典型示例 - 如果发动机机油压力开关 (1) 位于缸体上,遵循步骤 3.a 至 3.c 以拆下发动机机油压力开关。
- 将发动机机油压力开关 (1) 和接头 (4) 作为一个组件从机油管 (2) 上拆下。
- 拆下垫圈 (3)。
- 从适配器 (4) 上拆下发动机机油压力开关 (1)。
Show/hide table
图 1 | g01307413 |
典型示例 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 5P-3413 | 管密封胶 | 1 |
注: 发动机机油压力开关可能位于气门机构盖或缸体中。 有关正确位置,请参阅技术规格, "发动机机油压力开关"。
- 如果发动机机油压力开关 (1) 位于气门机构盖上,安装发动机机油压力开关并拧紧至扭矩
11 N·m (97 lb in) 。Show/hide table图 4 g01307450 典型示例 - 如果发动机机油压力开关 (1) 位于缸体上,遵循步骤 2.a 至 2.c 以安装发动机机油压力开关。
- 将发动机机油压力开关 (1) 安装至适配器 (4)。 拧紧发动机机油压力开关至扭矩为
23 N·m (17 lb ft) 。注: 如果安装使用过的发动机机油压力开关,将一薄层工具 (A) 涂敷在发动机机油压力开关的螺纹上。
- 将新垫圈 (3) 放到机油管 (2) 上并将发动机机油压力开关 (1) 和适配器 (4) 的组件安装到缸体上。
- 拧紧适配器 (4) 至扭矩为
11 N·m (97 lb in) 。
- 将发动机机油压力开关 (1) 安装至适配器 (4)。 拧紧发动机机油压力开关至扭矩为
- 将线束组件(未显示)连接到发动机机油压力开关 (1) 上。
Show/hide table
图 3 | g01307413 |
典型示例 |
注: 如果安装使用过的发动机机油压力开关,将一薄层工具 (A) 涂敷在发动机机油压力开关的螺纹上。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
AD55B Underground Articulated Truck Steering System General Information
AD55B Underground Articulated Truck Belt - Inspect/Replace
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Maximum Reverse Gear - Program
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Maximum Forward Gear - Program
D6G Series II Track-Type Tractor Machine Systems Bulldozer Blade - Remove
657G Wheel Tractor-Scraper Wheel Tractor Power Train Scavenge Pump and Mounting (Flywheel) - Install
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Flywheel Scavenge) - Assemble
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Flywheel Scavenge) - Disassemble
2006/10/02 Use Only Cleaning Agents that are Water Based with the 212-1503 Parts Washer Kit {0680}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Turbocharger - Remove and Install