Fan and Gear Motor (Hydraulic Fan) - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 8H-0700 | 拉拔器组件 | 1 |
开始:
- 释放液压系统油压。 请参阅拆解和组装, "液压系统压力 - 释放"。
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接所有管路、软管和管子。 这将有助于防止液体泄漏和防止污染物进入系统。
- 打开后门。 断开软管组件 (1)、 (2) 和 (3)。
Show/hide table
图 2 g01289881 - 拆下螺栓 (4) 并断开支撑 (5)。
Show/hide table
图 3 g01289907 - 将适当的起吊设备连接至防护罩组件 (8) 上。 防护罩 (8) 和齿轮马达的组合重量约为
70 kg (155 lb) 。 松开锁销 (7) 和 (10)。 拆下螺栓 (6) 和 (9)。 拆下护罩组件 (8)。Show/hide table图 4 g01289908 - 拆下螺栓 (11)。
Show/hide table
图 5 g01289910 - 重新放置防护罩 (8) 和齿轮马达。 拆下螺栓 (12) 和风扇 (13)。
Show/hide table
图 6 g01289911 - 拆下螺母 (14)。
Show/hide table
图 7 g01289978 - 使用工具 (A),拆下毂 (15)。
Show/hide table
图 8 g01289979 - 重新放置防护罩 (8) 和齿轮马达。 拆下螺栓 (16) 和挡块 (17)。
Show/hide table
图 9 g01289980 - 拆下螺栓 (18) 和齿轮马达 (19)。
Show/hide table
图 10 g01289981 - 拆下螺栓 (22)。 拆下支撑 (21) 和风扇护罩 (20)。
Show/hide table
图 1 | g01289880 |
Caterpillar Information System:
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Install
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Remove
953D Track-Type Loader Machine Systems Lift Cylinder - Remove and Install
Machining and Welding Information for Underground Articulated Trucks Front Frame
Machining and Welding Information for Underground Articulated Trucks Rear Frame
Load Haul Dump Machine Machining & Welding Information Consumables
D11R Starter Solenoid Connections{1467} D11R Starter Solenoid Connections{1467}
657G Wheel Scraper Power Train Final Drive and Wheel - Install
657G Wheel Scraper Power Train Final Drive and Wheel - Remove
D6K Track-Type Tractor Electrohydraulic Power Train Track Roller
657G Wheel Scraper Power Train Power Train Guard (Transmission) - Remove and Install
2006/07/31 Bearing Inserts Are Now Used in Frame Steering Bracket {7051, 7073}
D7G Series 2 and D7G Series II Track-Type Tractors Cutting Edges and End Bits - Inspect/Replace
D7G Series 2 and D7G Series II Track-Type Tractors Battery Disconnect Switch
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Fuses and Circuit Breakers - Replace/Reset
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Install
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Install
D7G Series 2 and D7G Series II Track-Type Tractors Radiator Pressure Cap - Clean/Replace
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Disassemble
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Assemble
D7G Series 2 and D7G Series II Track-Type Tractors Ripper Tip and Shank Protector - Inspect/Replace
993K Wheel Loader Hydraulic Oil Tank Filter Element (Case Drain) (Steering) (Brake) - Replace
993K Wheel Loader Hydraulic System Oil (Steering) (Brake) - Change