Piston Pump (Implement) - Install
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 将适当的起吊设备连接到活塞泵 (7) 上。 活塞泵 (7) 的重量约为
36 kg (80 lb) 。 安置活塞泵 (7),然后安装螺栓 (8)。Show/hide table图 2 g01289961 - 连接软管组件 (6)。
Show/hide table
图 3 g01289885 - 连接软管组件 (4) 和软管 (5)。
Show/hide table
图 4 g01289884 - 连接软管组件 (2)。 连接弯管 (3)。
Show/hide table
图 5 g01289883 - 连接软管组件 (1)。
Show/hide table
图 1 | g01289886 |
结束:
- 安装齿轮泵。 请参考拆解和组装, "齿轮泵(风扇驱动)- 安装"。
Caterpillar Information System:
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Remove
953D Track-Type Loader Machine Systems Lift Cylinder - Remove and Install
Machining and Welding Information for Underground Articulated Trucks Front Frame
Machining and Welding Information for Underground Articulated Trucks Rear Frame
Load Haul Dump Machine Machining & Welding Information Consumables
D11R Starter Solenoid Connections{1467} D11R Starter Solenoid Connections{1467}
657G Wheel Scraper Power Train Final Drive and Wheel - Install
657G Wheel Scraper Power Train Final Drive and Wheel - Remove
D6K Track-Type Tractor Electrohydraulic Power Train Track Roller
657G Wheel Scraper Power Train Power Train Guard (Transmission) - Remove and Install
2006/07/31 Bearing Inserts Are Now Used in Frame Steering Bracket {7051, 7073}
Underground Articulated Trucks Truck Payload Measurement System Service Tools
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Cutting Edges and End Bits - Inspect/Replace
D7G Series 2 and D7G Series II Track-Type Tractors Battery Disconnect Switch
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Fuses and Circuit Breakers - Replace/Reset
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Install
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Install
D7G Series 2 and D7G Series II Track-Type Tractors Radiator Pressure Cap - Clean/Replace
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Disassemble
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Assemble
D7G Series 2 and D7G Series II Track-Type Tractors Ripper Tip and Shank Protector - Inspect/Replace
993K Wheel Loader Hydraulic Oil Tank Filter Element (Case Drain) (Steering) (Brake) - Replace