Steering Control Valve - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
开始:
- 释放液压系统压力。 请参阅拆解和组装, "液压系统压力 - 释放"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
注: 为便于安装,在所有管路、所有软管、所有导线及所有管上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和有助于防止污染物进入系统。
- 将液压油箱中的油排入合适的容器以便保存或废弃这些油。 请参阅操作和保养手册, "液压系统油 - 更换"。
- 断开软管组件 (1) 和 (2) 。
Show/hide table
图 1 | g01290087 |
- 断开软管组件 (3) 和 (4) 。
Show/hide table
图 2 | g01290088 |
- 断开软管组件 (6) 。 将工具 (A) 和适当的起吊设备连接在转向控制阀 (7) 上。 转向控制阀 (7) 的重量约为 75 kg (165 lb)。 卸下螺栓 (5) 。 卸下转向控制阀 (7) 。
Show/hide table
图 3 | g01290089 |
Caterpillar Information System:
D7G Series 2 and D7G Series II Track-Type Tractors Battery Disconnect Switch
D7G Series 2 and D7G Series II Track-Type Tractors Cutting Edges and End Bits - Inspect/Replace
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Install
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Remove
953D Track-Type Loader Machine Systems Lift Cylinder - Remove and Install
Machining and Welding Information for Underground Articulated Trucks Front Frame
Machining and Welding Information for Underground Articulated Trucks Rear Frame
Load Haul Dump Machine Machining & Welding Information Consumables
D11R Starter Solenoid Connections{1467} D11R Starter Solenoid Connections{1467}
657G Wheel Scraper Power Train Final Drive and Wheel - Install
657G Wheel Scraper Power Train Final Drive and Wheel - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Fuses and Circuit Breakers - Replace/Reset
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Install
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Install
D7G Series 2 and D7G Series II Track-Type Tractors Radiator Pressure Cap - Clean/Replace
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Disassemble
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Assemble
D7G Series 2 and D7G Series II Track-Type Tractors Ripper Tip and Shank Protector - Inspect/Replace
993K Wheel Loader Hydraulic Oil Tank Filter Element (Case Drain) (Steering) (Brake) - Replace
993K Wheel Loader Hydraulic System Oil (Steering) (Brake) - Change
953D Track-Type Loader Power Train Piston Pump (Hydrostatic) - Install - Right Side
993K Wheel Loader Hydraulic System Oil Level (Steering) (Brake) - Check
953D Track-Type Loader Engine Supplement Refrigerant Compressor - Remove and Install