Steering Control Valve - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 将工具 (A) 和适当的起吊设备连接在转向控制阀 (7) 上。 转向控制阀 (7) 的重量约为 75 kg (165 lb)。 安置转向控制阀 (7) 。 安装螺栓 (5) 。 连接软管组件 (6) 。
Show/hide table
图 1 | g01290089 |
- 连接软管组件 (3) 和 (4) 。
Show/hide table
图 2 | g01290088 |
- 连接软管组件 (1) 和 (2) 。
Show/hide table
图 3 | g01290087 |
- 给液压油箱加油。 请参阅操作和保养手册, "液压系统油 - 更换"。
Caterpillar Information System:
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Install
D7G Series 2 and D7G Series II Track-Type Tractors Fuses and Circuit Breakers - Replace/Reset
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Battery Disconnect Switch
D7G Series 2 and D7G Series II Track-Type Tractors Cutting Edges and End Bits - Inspect/Replace
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Install
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Remove
953D Track-Type Loader Machine Systems Lift Cylinder - Remove and Install
Machining and Welding Information for Underground Articulated Trucks Front Frame
Machining and Welding Information for Underground Articulated Trucks Rear Frame
Load Haul Dump Machine Machining & Welding Information Consumables
D7G Series 2 and D7G Series II Track-Type Tractors Radiator Pressure Cap - Clean/Replace
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Disassemble
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Assemble
D7G Series 2 and D7G Series II Track-Type Tractors Ripper Tip and Shank Protector - Inspect/Replace
993K Wheel Loader Hydraulic Oil Tank Filter Element (Case Drain) (Steering) (Brake) - Replace
993K Wheel Loader Hydraulic System Oil (Steering) (Brake) - Change
953D Track-Type Loader Power Train Piston Pump (Hydrostatic) - Install - Right Side
993K Wheel Loader Hydraulic System Oil Level (Steering) (Brake) - Check
953D Track-Type Loader Engine Supplement Refrigerant Compressor - Remove and Install
993K Wheel Loader Hydraulic System Oil Sample (Steering) (Brake) - Obtain
993K Wheel Loader Hydraulic Tank Breaker Relief Valve (Steering) (Brake) - Clean
AD45B Underground Articulated Truck Differential and Final Drive Oil Level - Check