Fan and Gear Motor (Hydraulic Fan) - Install
- 安装风扇防护罩 (20) 和支撑 (21)。 安装螺栓 (22)。
Show/hide table
图 2 g01289980 - 安装齿轮马达 (19) 和螺栓 (18)。
Show/hide table
图 3 g01290070 - 安装挡块 (17) 和螺栓 (16)。
Show/hide table
图 4 g01290071 - 安装毂 (15) 和螺母 (14)。 拧紧螺母 (14) 以完全座入毂 (15)。
Show/hide table
图 5 g01289910 - 重新放置防护罩 (8) 和齿轮马达。 安装风扇 (13) 和螺栓 (12)。
Show/hide table
图 6 g01289908 - 重新放置防护罩和风扇马达。 安装后风扇防护罩,然后安装螺栓 (11)。
Show/hide table
图 7 g01289907 - 将适当的起吊设备连接至防护罩组件 (8) 上。 防护罩 (8) 和齿轮马达的组合重量约为
70 kg (155 lb) 。 安装防护罩组件 (8) 以及螺栓 (6) 和 (9)。 接合锁销 (7) 和 (10)。Show/hide table图 8 g01289881 - 连接支撑 (5),然后安装螺栓 (4)。
Show/hide table
图 9 g01289880 - 连接软管组件 (1)、 (2) 和 (3)。 关闭后门。
Show/hide table
图 1 | g01289981 |
Caterpillar Information System:
D7G Series 2 and D7G Series II Track-Type Tractors Fuses and Circuit Breakers - Replace/Reset
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Battery Disconnect Switch
D7G Series 2 and D7G Series II Track-Type Tractors Cutting Edges and End Bits - Inspect/Replace
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Install
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Remove
953D Track-Type Loader Machine Systems Lift Cylinder - Remove and Install
Machining and Welding Information for Underground Articulated Trucks Front Frame
Machining and Welding Information for Underground Articulated Trucks Rear Frame
Load Haul Dump Machine Machining & Welding Information Consumables
D11R Starter Solenoid Connections{1467} D11R Starter Solenoid Connections{1467}
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Install
D7G Series 2 and D7G Series II Track-Type Tractors Radiator Pressure Cap - Clean/Replace
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Disassemble
953D Track-Type Loader Machine Systems Gear Motor (Fan) - Assemble
D7G Series 2 and D7G Series II Track-Type Tractors Ripper Tip and Shank Protector - Inspect/Replace
993K Wheel Loader Hydraulic Oil Tank Filter Element (Case Drain) (Steering) (Brake) - Replace
993K Wheel Loader Hydraulic System Oil (Steering) (Brake) - Change
953D Track-Type Loader Power Train Piston Pump (Hydrostatic) - Install - Right Side
993K Wheel Loader Hydraulic System Oil Level (Steering) (Brake) - Check
953D Track-Type Loader Engine Supplement Refrigerant Compressor - Remove and Install
993K Wheel Loader Hydraulic System Oil Sample (Steering) (Brake) - Obtain
993K Wheel Loader Hydraulic Tank Breaker Relief Valve (Steering) (Brake) - Clean