Final Drive and Wheel - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 155-3597     | 车轮锲块     | 4     |
B     | 4C-5809     | 电动液压泵总成     | 1     |
9U-7536 | 起吊台     | 2     | |
C     | 138-7575     | 连杆支架     | 2     |
E     | 138-7574     | 连杆支架     | 1     |
F     | 180-3033     | 千斤顶支座     | 2     |
G     | 1U-9200     | 杠杆式拔拉起重机     | 1     |
138-7575 | 连杆支架     | 1     | |
H     | 140-7742     | 套筒     | 1     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 将工具 (C) 、工具 (H) 和适当的起吊设备,将齿圈和轮毂 (12) 安置在机器上。 齿圈和轮毂 (12) 的重量约为 172 kg (380 lb)。
Show/hide table
图 1 | g01289714 |
- 安装护圈 (10) 和五个等间距螺栓 (9) 。
Show/hide table
图 2 | g01289716 |
Show/hide table
图 3 | g01290925 |
Show/hide table
图 4 | g01289696 |
- 卸下工具 (G) 。
- 转动车轮,拧紧螺栓 (9) 至扭矩为 35 N·m (26 lb ft)。 请参考图 3 中的正确紧固顺序。
- 转动车轮,拧紧螺栓 (9) 至扭矩为 70 N·m (52 lb ft)。 请参考图 3 中的正确紧固顺序。
- 测量护圈 (10) 端面到壳体组件端面的深度。 记录平均深度为尺寸 (X) 。
- 安装工具 (G) 。
- 测量护圈 (10) 的厚度。 将该测量值记录为尺寸 (Y) 。
Show/hide table
图 5 | g01289719 |
- 尺寸 (X) 减去尺寸 (Y) ,记录该测量值为尺寸 (Z) 。
- 卸下护圈 (10) ,调整垫片组,以获得尺寸 (Z) 加上 0.18 mm (0.007 in)。
- 安装垫片组 (11) (图上未显示)、护圈 (10) 和螺栓 (9) 。
Show/hide table
图 6 | g01289720 |
Show/hide table
图 7 | g01289721 |
Show/hide table
图 8 | g01289696 |
- 卸下工具 (G) 。
- 转动车轮,拧紧螺栓 (9) 至扭矩为 250 ± 25 N·m (184 ± 18 lb ft)。 请参考图 7 中的正确紧固顺序。
- 安装 O 形密封圈 (8) 。
Show/hide table
图 9 | g01285897 |
- 使用工具 (E) 和适当的起吊设备,将行星齿轮托架 (6) 安装在半轴 (5) 上。 行星齿轮托架 (6) 的重量约为 363 kg (800 lb)。
注: 半轴 (5) 提供平衡作用。
Show/hide table
图 10 | g01289681 |
Show/hide table
图 11 | g01289675 |
- 使用工具 (C) ,将行星齿轮托架 (6) 和半轴 (5) 安置在机器上。 行星齿轮托架 (6) 和半轴 (5) 的重量约为 433 kg (955 lb)。
- 安装螺栓 (7) 。
- 使用适当的起吊设备,从行星齿轮托架 (6) 上卸下半轴 (5) 。 半轴 (5) 的重量约为 70 kg (155 lb)。
Show/hide table
图 12 | g01285893 |
- 分离停车制动器。
Show/hide table
图 13 | g01289665 |
- 转动螺栓 (2) ,向上移动松紧张紧器 (1) 。
- 安装销 (4) 。
- 转动螺栓 (2) ,限定松紧调整器 (1) 的行程距离为 50 ± 3 mm (2 ± 0.12 in)。
- 拧紧螺栓 (3) 。
- 使用工具 (B) ,将机器降至地面。
Show/hide table
图 14 | g01289664 |
- 施加停车制动器,从前轮上卸下工具 (A) 。
Show/hide table
图 15 | g01100962 |
End By:
- 安装半轴。 请参阅 拆解和组装, "半轴 - 安装"。
- 安装传动系防护罩。 请参阅 拆解和组装, "变速箱传动系防护罩 - 拆卸和安装"。
Caterpillar Information System:
657G Wheel Scraper Power Train Final Drive and Wheel - Remove
D6K Track-Type Tractor Electrohydraulic Power Train Track Roller
657G Wheel Scraper Power Train Power Train Guard (Transmission) - Remove and Install
2006/07/31 Bearing Inserts Are Now Used in Frame Steering Bracket {7051, 7073}
Underground Articulated Trucks Truck Payload Measurement System Service Tools
D7G Series 2 and D7G Series II Track-Type Tractors Condenser (Refrigerant) - Clean
D7G Series 2 and D7G Series II Track-Type Tractors Emissions Certification Film
D7G Series 2 and D7G Series II Track-Type Tractors Fuel Tank Cap and Strainer - Clean
Installation Instructions for the 291-1184 Secondary Steering Group (Kit) {4300} Installation Instructions for the 291-1184 Secondary Steering Group (Kit) {4300}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Power Train Guard (Transmission) - Remove and Install
953D Track-Type Loader Machine Systems Cab - Install
953D Track-Type Loader Machine Systems Cab - Remove
D11R Starter Solenoid Connections{1467} D11R Starter Solenoid Connections{1467}
Load Haul Dump Machine Machining & Welding Information Consumables
Machining and Welding Information for Underground Articulated Trucks Rear Frame
Machining and Welding Information for Underground Articulated Trucks Front Frame
953D Track-Type Loader Machine Systems Lift Cylinder - Remove and Install
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Remove
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Install
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Cutting Edges and End Bits - Inspect/Replace
D7G Series 2 and D7G Series II Track-Type Tractors Battery Disconnect Switch
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Fuses and Circuit Breakers - Replace/Reset