Track Roller
Show/hide table
 | |
| Illustration 1 | g03423068 |
Show/hide table
| Specification for 240-8933 Track Roller | |||
| Item | Qty | Part | Specification Description |
| 1 | 2 | 171-5883 Duo-Cone Seal Gp | The rubber toric seals and all the contacting surfaces must be clean and dry at assembly. Just before assembly, apply a thin layer of 6V-4876 Lubricant to the contacting surfaces of the metal seal rings. The seal rings must be assembled square. The rubber toric seal should not bulge and the rubber toric seal should not twist. |
| 2 | 2 | 1H-8128 O-Ring Seal | During assembly, lubricate two O-ring seals (2) and the mating surface of the bushing (3) with the lubricant that is being sealed. |
| 3 | 2 | 124-8248 Bushing | |
| 4 | 2 | 217-6359 Collar | Lubricate the shaft (5) in the seating surface of the collar (4) with the lubricant that is being sealed. |
| 5 | 1 | 217-6358 Shaft | |
| 6 | 1 | - | The plug must not be recessed below the surface of the 6Y-0454 Stopper As . |
| - | - | - | Minimum end play of the shaft in axial direction is 0.25 mm (0.010 inch). Maximum end play of the shaft in axial direction is 1.23 mm (0.048 inch). |
Caterpillar Information System:
657G Wheel Scraper Power Train Power Train Guard (Transmission) - Remove and Install
2006/07/31 Bearing Inserts Are Now Used in Frame Steering Bracket {7051, 7073}
Underground Articulated Trucks Truck Payload Measurement System Service Tools
D7G Series 2 and D7G Series II Track-Type Tractors Condenser (Refrigerant) - Clean
D7G Series 2 and D7G Series II Track-Type Tractors Emissions Certification Film
D7G Series 2 and D7G Series II Track-Type Tractors Fuel Tank Cap and Strainer - Clean
Installation Instructions for the 291-1184 Secondary Steering Group (Kit) {4300} Installation Instructions for the 291-1184 Secondary Steering Group (Kit) {4300}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Power Train Guard (Transmission) - Remove and Install
953D Track-Type Loader Machine Systems Cab - Install
953D Track-Type Loader Machine Systems Cab - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Fuel Tank Water and Sediment - Drain
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Braking System Brake Accumulator
657G Wheel Scraper Power Train Final Drive and Wheel - Remove
657G Wheel Scraper Power Train Final Drive and Wheel - Install
D11R Starter Solenoid Connections{1467} D11R Starter Solenoid Connections{1467}
Load Haul Dump Machine Machining & Welding Information Consumables
Machining and Welding Information for Underground Articulated Trucks Rear Frame
Machining and Welding Information for Underground Articulated Trucks Front Frame
953D Track-Type Loader Machine Systems Lift Cylinder - Remove and Install
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Remove
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Install
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Cutting Edges and End Bits - Inspect/Replace
D7G Series 2 and D7G Series II Track-Type Tractors Battery Disconnect Switch