Engine Oil Level - Check
Show/hide table
热油和热的部件可能会导致人员受伤。 请勿让热的液压油或热的零部件与皮肤接触。 |
Show/hide table
注意 |
---|
发动机曲轴箱注油时,油不要过少或过满。 任何一种情况都会造成发动机损坏。 |
Show/hide table
图 1 | g01156691 |
油位表 (1) 位于牵引机右侧。
- 将机器停放在平地上。 降下铲运斗。
- 打开机器右侧的发动机检修门。
- 发动机运转时,检查油位表 "1" 的 (低怠速 (LOW IDLE)) 侧。 保持机油油位在"添加(ADD)" 和"满(FULL)"两个标记之间。
当发动机停机时,检查油位表 (1) 的"发动机停止(ENGINE STOPPED)"侧。 将机油油位保持在"低 (LOW)"和"满 (FULL)"标记之间。
Show/hide table图 2 g01156747 注: 在陡坡上操作机器时,发动机曲轴箱的油位必须在油位表 (1) 的"发动机停止(ENGINE STOPPED)"侧的"满(FULL)"标记处。
- 清洁机油加注口盖 (2) 周围区域。 拆下机油加注口盖。 如有需要,加注机油。
- 清洁并安装机油加注口盖。
- 关闭发动机检修盖。
Caterpillar Information System:
657G Wheel Tractor-Scraper Cooling System Pressure Cap - Clean/Replace
637G Wheel Tractor-Scraper Engine Oil (High Speed) and Oil Filter - Change
904B Wheel Loader Engine Supplement Water Temperature Regulator - Remove and Install
C9 Engines for Caterpillar Built Machines Fan Drive - Remove
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0489 - FMI 03
631G Wheel Tractor-Scraper Engine Oil (High Speed) and Oil Filter - Change
657G Wheel Tractor-Scraper Cooling System Coolant Sample (Level 1) - Obtain
C9 Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C9 Engines for Caterpillar Built Machines Cylinder Head - Install
904B Wheel Loader Engine Supplement Battery and Battery Cable - Separate and Connect
657G Wheel Tractor-Scraper Engine Air Filter Service Indicator - Inspect/Replace
621G Wheel Tractor-Scraper Engine Air Filter Service Indicator - Inspect/Replace - If Equipped
657G Wheel Tractor-Scraper Cutting Edges and End Bits - Inspect/Replace
AD45B Underground Articulated Truck Power Train Electronic Control System MID 027 - CID 0190 - FMI 02
AD45B Underground Articulated Truck Power Train Electronic Control System MID 027 - CID 0190 - FMI 08
966H and 972H Wheel Loaders Machine Systems Lift Arms - Remove
966H and 972H Wheel Loaders Machine Systems Lift Arms - Install
637G Wheel Tractor-Scraper Engine Oil Level - Check
631G Wheel Tractor-Scraper Engine Oil Sample - Obtain
2005/04/18 A New Aftercooler Gasket and a New Torque Tightening Sequence is Now Used {1063}
Machining of Replacement Sleeve Bearings{1206, 1212, 1234} Machining of Replacement Sleeve Bearings{1206, 1212, 1234}
637G Wheel Tractor-Scraper Engine Oil Sample - Obtain
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0489 - FMI 04
904B Wheel Loader Power Train Worksheets