Final Drive - Disassemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7574 | Link Bracket | 2 |
B | 2P-8312 | Retaining Ring Pliers | 1 |
Start By:
- Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Use Tooling (B) in order to remove retaining ring (3). Remove sun gear (2). Remove spacer (1).
Show/hide table
Illustration 2 g00829516 - Remove planetary shafts (4).
Show/hide table
Illustration 3 g00829518 - Use Tooling (B) in order to remove retaining ring (5).
- Repeat Step 3 in order to remove the retaining rings from the remaining planetary shafts.
Show/hide table
Illustration 4 g01050663 - Remove planetary gears (7). Remove seal (6).
Show/hide table
Illustration 5 g01050664 - Remove thrust washers (8), roller bearings (9), and spacers (10) from planetary gear (7).
- Repeat Step 6 in order to disassemble the remaining two planetary gears.
Show/hide table
Illustration 6 g00829524 - Support ring gear (11) and hub (12) with blocking. The weight of hub (12) is approximately
50 kg (110 lb) . The weight of ring gear (11) is approximately45 kg (100 lb) .Show/hide tableIllustration 7 g00829569 - Remove two opposing retainers (13) and install Tooling (A) and a suitable lifting device. Remove the other retainers (13).
Show/hide table
Illustration 8 g01050665 - Use Tooling (A) and the suitable lifting device to remove hub (12) from ring gear (11).
Show/hide table
Illustration 1 | g01050662 |
Caterpillar Information System:
966H and 972H Wheel Loaders Machine Systems Electrohydraulic Control - Remove
623G Wheel Tractor-Scraper Machine Systems Check Valve (Carry) - Disassemble
2001/10/29 Correction to Disassembly and Assembly , "Bucket-Install" {0645, 6101, 6102}
D10R Track-Type Tractor Power Train Chrome Bearing - Remove and Install
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Digital Sensor Supply Circuit - Test
D3G, D4G and D5G Hystat Track-Type Tractors Power Train Final Drive and Sprocket - Disassemble
631G Wheel Tractor Power Train Transmission and Transfer Gears - Connect
D6N Track-Type Tractor Power Train Priority Valve
D3G, D4G and D5G Track-Type Tractors Parking Brake
631G Wheel Tractor Power Train Transmission and Transfer Gears - Separate
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Sensors and Electrical Connectors
3056 Engines Engine Oil Pump
D3G, D4G and D5G Hystat Track-Type Tractors Engine Supplement Water Pump - Remove
3056E Industrial Engine Camshaft
2001/11/12 A New Rear Housing Assembly is Available {1157}
3056 Engines Connecting Rod
D3G, D4G and D5G Hystat Track-Type Tractors Engine Supplement Water Pump - Install
3056 Engines Cylinder Head
D6R Series II Track-Type Tractor Power Train Bevel and Transfer Gears - Disassemble
621G and 623G Wheel Tractor Power Train Final Drive - Assemble
621G and 627G Wheel Tractor-Scrapers Machine Systems Air Tank - Remove and Install
D6R Series II Track-Type Tractor Power Train Bevel and Transfer Gears - Assemble
D3G, D4G and D5G Track-Type Tractors Piston Pump (Hydrostatic)