Chrome Bearing - Remove and Install
Removal Procedure
Start By:
- Remove the front track roller frame. Refer to Disassembly and Assembly, "Front Track Roller Frame - Remove".
Note: The front track roller frame does not need to be completely removed from the machine in order to replace the chrome bearing.
- Install a strap to recoil spring housing (1). Remove the chrome bearing to the strap. Place a suitable jack stand under the recoil spring housing. Remove the strap.
Show/hide table
Illustration 1 | g00829677 |
- Remove chrome bearing (2) from front track roller frame (3) and the recoil spring housing. Attach the strap and remove the suitable jack stand.
Installation Procedure
- Use the strap in order to raise the rear of the track roller frame (3) to 15 degrees or more. Place a suitable jack stand under the recoil spring housing in order to hold the track roller frame in position. Remove the strap.
Show/hide table
Illustration 2 | g00829677 |
- Raise the temperature of the chrome bearing to 175 °C (347 °F). Slide chrome bearing (2) on the recoil spring housing to the jack stand. Attach the strap and remove the jack stand. Slide the chrome bearing to the larger diameter of the recoil spring housing.
- Carefully slide the chrome bearing on recoil spring housing (1). Use a wood block to apply constant pressure on the chrome bearing. The wood block will help prevent the chrome bearing from bouncing away from the proper area of installation.
Note: Do not allow the temperature of the chrome bearing to cool during the installation procedure. If the chrome bearing is installed in an incorrect position, the chrome bearing must be removed and a new chrome bearing must be installed.
End By: Install the front track roller frame. Refer to Disassembly and Assembly, "Front Track Roller Frame - Install".
Caterpillar Information System:
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Digital Sensor Supply Circuit - Test
D3G, D4G and D5G Hystat Track-Type Tractors Power Train Final Drive and Sprocket - Disassemble
631G Wheel Tractor Power Train Transmission and Transfer Gears - Connect
D6N Track-Type Tractor Power Train Priority Valve
D3G, D4G and D5G Track-Type Tractors Parking Brake
631G Wheel Tractor Power Train Transmission and Transfer Gears - Separate
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Sensors and Electrical Connectors
2001/10/15 Correction to Specification , "Track Rollers" {4180}
631G Wheel Tractor Power Train Transmission, Torque Converter, Transfer Gears and Differential - Install
D3G, D4G and D5G Hystat Track-Type Tractors Power Train Final Drive and Sprocket - Install
D5N Track-Type Tractor Transmission Oil Filter
2001/10/29 Correction to Disassembly and Assembly , "Bucket-Install" {0645, 6101, 6102}
623G Wheel Tractor-Scraper Machine Systems Check Valve (Carry) - Disassemble
966H and 972H Wheel Loaders Machine Systems Electrohydraulic Control - Remove
621G and 623G Wheel Tractor Power Train Final Drive - Disassemble
3056 Engines Engine Oil Pump
D3G, D4G and D5G Hystat Track-Type Tractors Engine Supplement Water Pump - Remove
3056E Industrial Engine Camshaft
2001/11/12 A New Rear Housing Assembly is Available {1157}
3056 Engines Connecting Rod
D3G, D4G and D5G Hystat Track-Type Tractors Engine Supplement Water Pump - Install
3056 Engines Cylinder Head
D6R Series II Track-Type Tractor Power Train Bevel and Transfer Gears - Disassemble