Final Drive - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7574 | Link Bracket | 2 |
B | 2P-8312 | Retaining Ring Pliers | 1 |
C | 9S-3263 | Thread Lock Compound | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components. To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly. Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination. |
- Support ring gear (11) with suitable blocking. Install Tooling (A) and a suitable lifting device to hub (12). Install hub (12) to ring gear (11). The weight of ring gear (11) is approximately
45 kg (100 lb) . The weight of hub (12) is approximately50 kg (110 lb) .Show/hide tableIllustration 2 g00829569 - Apply Tooling (C) onto the bolts that attach retainers (13). Install two opposing retainers (13) and the bolts before removal of Tooling (A). Install the other retainers (13) and the bolts.
Show/hide table
Illustration 3 g01050664 - Install roller bearings (9), spacers (10), and thrust washers (8) into planetary gear (7).
- Repeat Step 3 in order to assemble the remaining two planetary gears.
Show/hide table
Illustration 4 g01050663 - Install seal (6). Install planetary gears (7).
Show/hide table
Illustration 5 g00829518 - Use Tooling (B) in order to install retaining ring (5).
- Repeat Step 6 in order to install the remaining two retaining rings.
Show/hide table
Illustration 6 g00829516 - Install planetary shafts (4).
Show/hide table
Illustration 7 g01050662 - Install spacer (1) and sun gear (2). Use Tooling (B) in order to install retaining ring (1).
Show/hide table
Illustration 1 | g00829571 |
End By:
- Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".
Caterpillar Information System:
D6R Series II Track-Type Tractor Power Train Bevel and Transfer Gears - Disassemble
3056 Engines Cylinder Head
D3G, D4G and D5G Hystat Track-Type Tractors Engine Supplement Water Pump - Install
3056 Engines Connecting Rod
2001/11/12 A New Rear Housing Assembly is Available {1157}
3056E Industrial Engine Camshaft
D3G, D4G and D5G Hystat Track-Type Tractors Engine Supplement Water Pump - Remove
3056 Engines Engine Oil Pump
621G and 623G Wheel Tractor Power Train Final Drive - Disassemble
966H and 972H Wheel Loaders Machine Systems Electrohydraulic Control - Remove
623G Wheel Tractor-Scraper Machine Systems Check Valve (Carry) - Disassemble
2001/10/29 Correction to Disassembly and Assembly , "Bucket-Install" {0645, 6101, 6102}
621G and 627G Wheel Tractor-Scrapers Machine Systems Air Tank - Remove and Install
D6R Series II Track-Type Tractor Power Train Bevel and Transfer Gears - Assemble
D3G, D4G and D5G Track-Type Tractors Piston Pump (Hydrostatic)
966H and 972H Wheel Loaders Machine Systems Electrohydraulic Control - Install
Installation of Automatic Lubrication for the 966G and the 972G Wheel Loaders{7540} Installation of Automatic Lubrication for the 966G and the 972G Wheel Loaders{7540}
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders Low Power/Poor or No Response to Throttle
3176C, 3196 and 3406E Engines for Caterpillar Built Machines 5 Volt Engine Pressure Sensor Supply Circuit - Test
G3500B Engines Fumes Disposal Filter Differential Pressure - Check
2001/10/08 An Improved Accumulator Spring Assembly is Now Used in the Valves for the Electronic Brake (EB) and the Electronic Clutch/Brake (ECB) {5051}
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader Cat Data Link Circuit - Test
966G Series II and 972G Series II Wheel Loaders Engine Supplement Hydraulic Oil Cooler - Remove and Install
D7R Series II Track-Type Tractor Hydraulic System Winch Control Valve