Window Wiper Motor (Rear) - Remove
Removal Procedure
Note: Put identification marks on all lines, hoses, wires, and tubes for installation purposes.
- Remove six bolts (1). Remove grill (2) .
Show/hide table
 | |
| Illustration 1 | g00744287 |
- Move the battery disconnect switch to the OFF. Disconnect both battery terminals.
- Raise cover (4) on wiper arm (3) .
Show/hide table
 | |
| Illustration 2 | g00636932 |
- Remove nut (5) from shaft (7) .
- Remove hose (6) from wiper arm (3) .
- Remove wiper arm (3) from shaft (7) .
- Remove cover (8) from shaft (7) .
Show/hide table
 | |
| Illustration 3 | g00636285 |
- Remove nut (9) from shaft (7) .
Show/hide table
 | |
| Illustration 4 | g00636295 |
- Remove two screws (10). Remove filter (11) .
Show/hide table
 | |
| Illustration 5 | g00636300 |
- Remove four torx screws (12) from cover (13) .
Show/hide table
 | |
| Illustration 6 | g00636310 |
- Remove one Torx screw (14) from the right side of cover (13) .
Show/hide table
 | |
| Illustration 7 | g00636312 |
- Remove two Torx screws (15) from the left side of cover (13) .
Show/hide table
 | |
| Illustration 8 | g00636319 |
- Remove cover (13) .
- Disconnect electrical connector (16) from wiper motor assembly (17) .
Show/hide table
 | |
| Illustration 9 | g00636484 |
- Remove two bolts (18). Remove wiper motor assembly (17) .
Show/hide table
 | |
| Illustration 10 | g00636351 |
- Loosen bolt (19) on arm (20). Remove arm (20) from the shaft of window wiper motor (21) .
Show/hide table
 | |
| Illustration 11 | g00636494 |
- Remove three bolts (22). Remove window wiper motor (21) from wiper motor assembly (17) .
Show/hide table
 | |
| Illustration 12 | g00636501 |
Caterpillar Information System:
515 Wheel Skidder and 525 Wheel Skidder Hydraulic and Steering System Control Valve (Hydraulic Retrieval Device)
C-9 Engines for Caterpillar Built Machines Cooling System - Check - Overheating
631E Series II, 633E Series II and 637E Series II Wheel Tractor Power Train Torque Converter Outlet Relief Valve Pressure - Test
992G Wheel Loader and 854G Wheel Dozer Braking System Oil Filter (Case Drain)
3056 Engine for Caterpillar Built Machines Crankshaft - Install
924G and 924Gz Wheel Loaders Power Train Transmission Pressures - Test and Adjust
C-9 Engines for Caterpillar Built Machines Excessive Engine Oil Consumption - Inspect
3056 Engine for Caterpillar Built Machines Crankshaft - Remove
924G and 924Gz Wheel Loaders Power Train NoSPIN Differential - Test
924G and 924Gz Wheel Loaders Power Train Limited Slip Differential Disc End Play Check - Check
3056 Engine for Caterpillar Built Machines Connecting Rod Bearings - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Pump - Remove - 3013, 3014, and 3024 Engines
C-9 Engines for Caterpillar Built Machines Cooling System - Test
992G Wheel Loader and 854G Wheel Dozer Steering System Pressure Switch (Filter Bypass)
C-9 Engines for Caterpillar Built Machines Water Pump - Test
Installing New Components for a Kickout and Positioner on a Track Loader{5109, 5112, 5132} Installing New Components for a Kickout and Positioner on a Track Loader{5109, 5112, 5132}
D9R Track-Type Tractor Lifting and Tying Down the Machine
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Carryback Weight Entering
992G Wheel Loader and 854G Wheel Dozer Steering System Relief Valve (Steering Pilot)
824G , 825G and 826G Landfill Compactor Maintenance Interval Schedule
980G Wheel Loader Braking System Limit Switch (Transmission Neutralizer)
3056 Engines Piston and Rings
924G and 924GZ Wheel Loaders Hydraulic System Ride Control Accumulator
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Calibration Weight Entering