Connecting Rod Bearings - Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean upper connecting rod bearing (4) and lubricate the bearing face with clean engine oil.
- Clean lower connecting rod cap (3) and the lower connecting rod bearing. Lubricate the bearing face with clean engine oil.
Note: Align the tabs on the connecting rod bearings with the tab grooves in the connecting rod.
- Pull the connecting rod into position against the crankshaft. The connecting rod may need to be rotated in order to prevent contact with the piston cooling jet.
- Install connecting rod cap (3) and the lower connecting rod bearing together in connecting rod (2).
- Install bolts (1) and the nuts in the connecting rod (2). Tighten bolts (1) to a torque of
155 N·m (114 lb ft) . Tighten the nuts to a torque of125 N·m (92 lb ft) . - Repeat Steps 1 through 5 for the remaining connecting rod bearings.
Show/hide table
| |
| Illustration 1 | g00893992 |
End By:
- Install the engine oil relief valve. Refer to Disassembly and Assembly, "Engine Oil Relief Valve - Remove and Install".
- Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Caterpillar Information System:
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Pump - Remove - 3013, 3014, and 3024 Engines
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Pump - Install - 3013, 3014, and 3024 Engines
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Bucket Volume Entering
924G and 924Gz Wheel Loaders Power Train Axle Housing and Bearing Preload - Adjust
988G Wheel Loader Machine Systems Blower Motor (Air Conditioner, Heater) - Remove
SR4 and SR4B Electric Power Generation Rewind Data Generator Identification
924G and 924Gz Wheel Loaders Power Train Differential Pinion Preload - Adjust
631E Series II, 633E Series II and 637E Series II Wheel Tractor Power Train Transmission Lubrication Relief Valve Pressure - Test
D10R, D11R and D11R Carrydozer Track-Type Tractors Implement Electronic Control System Implement Electronic Control (Ripper)
824G , 825G and 826G Landfill Compactor Brake Discs - Check
3056 Engine for Caterpillar Built Machines Connecting Rod Bearings - Remove
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Check Valve (Ride Control)
924G and 924Gz Wheel Loaders Power Train Limited Slip Differential Disc End Play Check - Check
924G and 924Gz Wheel Loaders Power Train NoSPIN Differential - Test
3056 Engine for Caterpillar Built Machines Crankshaft - Remove
C-9 Engines for Caterpillar Built Machines Excessive Engine Oil Consumption - Inspect
924G and 924Gz Wheel Loaders Power Train Transmission Pressures - Test and Adjust
3056 Engine for Caterpillar Built Machines Crankshaft - Install
992G Wheel Loader and 854G Wheel Dozer Braking System Oil Filter (Case Drain)
631E Series II, 633E Series II and 637E Series II Wheel Tractor Power Train Torque Converter Outlet Relief Valve Pressure - Test
C-9 Engines for Caterpillar Built Machines Cooling System - Check - Overheating
515 Wheel Skidder and 525 Wheel Skidder Hydraulic and Steering System Control Valve (Hydraulic Retrieval Device)
902 and 906 Compact Wheel Loaders Machine Systems Window Wiper Motor (Rear) - Remove
C-9 Engines for Caterpillar Built Machines Cooling System - Test