Housing (Front) - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean old gasket material (11) from the contact surface of front housing (8) and the timing gear plate. Install a new gasket.
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets or the O-ring seals are damaged or worn, use new parts for replacement.
Show/hide table
Illustration 1 | g00529392 |
- Install bearing (12), if equipped. If the bearing is worn or damaged, use a new part for replacement.
- Install O-ring seal (13) onto cover (9), if equipped.
- Install a new crankshaft front seal (10), if the crankshaft front seal was removed. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
Show/hide table
Illustration 2 | g00529391 |
- If equipped, install camshaft gear cover (9) onto front housing (8) .
- Install front housing (8) .
Show/hide table
Illustration 3 | g00529390 |
- Install bolts (7) in order to fasten front housing (8) onto the cylinder block.
- Install the washers and six bolts (6) in order to secure front housing (8) onto engine oil pan.
- Install cover (5) for fuel injection pump gear.
- Install the washers and five bolts (4) in order to secure cover (5) for fuel injection pump gear onto front housing (8) .
- If equipped, install the washers and bolts (3) in order to secure camshaft gear cover (9) onto front housing (8) .
- Install fan pulley (2) .
Show/hide table
Illustration 4 | g00560210 |
- Install the washers and four bolts (1) in order to secure fan pulley (2) onto the water pump.
End By:
- Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
- Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
Caterpillar Information System:
D9R Track-Type Tractor Machine Systems Refrigerant Condenser - Remove and Install
D9R Track-Type Tractor Machine Systems Refrigerant Compressor - Remove and Install
D9R Track-Type Tractor Machine Systems Air Conditioner Dryer - Remove and Install
D9R Track-Type Tractor Machine Systems Air Conditioner and Heater Fan Motor - Remove and Install
D9R Track-Type Tractor Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
D9R Track-Type Tractor Machine Systems Steering Motor - Assemble
D9R Track-Type Tractor Machine Systems Steering Motor - Disassemble
D9R Track-Type Tractor Machine Systems Steering Motor - Install
D9R Track-Type Tractor Machine Systems Steering Motor - Remove
D9R Track-Type Tractor Machine Systems Governor Control Linkage and Decelerator - Install
D9R Track-Type Tractor Machine Systems Governor Control Linkage and Decelerator - Remove
D9R Track-Type Tractor Machine Systems Bulldozer and Tilt Control Linkage - Remove
623F Wheel Tractor-Scraper Power Train Retarder Hydraulic Control Valve - Disassemble
994D Air System Wheel Loader Air Dryer - Check
545 Wheel Skidder Hydraulic and Steering System Steering Cylinder
515 Wheel Skidder and 525 Wheel Skidder Transmission and Grapple Electronic Control System Start Switch (Key)
623F Wheel Tractor-Scraper Power Train Retarder Hydraulic Control Valve - Assemble
515 Wheel Skidder and 525 Wheel Skidder Transmission and Grapple Electronic Control System Start Relay
D9R Track-Type Tractor Stopping the Engine
963B Track-Type Loader Engine Oil and Filter - Change
D9R Track-Type Tractor Machine Systems Refrigerant Accumulator - Remove and Install
D9R Track-Type Tractor Engine Air Filter Primary Element - Clean/Replace
D9R Track-Type Tractor Machine Systems Refrigerant Evaporator Core and Heater Core - Remove and Install
D9R Track-Type Tractor Machine Systems Steering Pump - Assemble