Steering Motor - Disassemble
拆解步骤
开始:
- 拆卸转向马达。 请参阅拆解和装配, "转向马达 - 拆卸"。
Show/hide table
所需工具     | |||
工具     | 零件号     | 说明     | 数量     |
A     | 5P-4758     | 挡圈钳     | 1     |
B     | 8B-7556     | 适配器     | 1     |
8B-7555 | 适配器     | 1     | |
0S-1575 | 螺栓(3/4 英寸 X 16 X 3)     | 2     | |
5H-1504 | 垫圈     | 2     | |
C     | 1P-2854     | 活动扳手     | 1     |
- 将密封缠绕在花键轴 (1) 上以保护密封件。
Show/hide table
图 1 | g00624660 |
- 使用塑料锤轻敲盖以便释放作用在挡圈 (2) 上的压力。
Show/hide table
图 2 | g00624673 |
- 使用工具 (A) 以拆下挡圈 (2) 。
- 使用两把螺丝刀拆卸前盖 (3) 。
Show/hide table
图 3 | g00624674 |
- 从椅背的前齿轮室盖上拆下 O 形密封圈和垫片。
- 如有必要拆下驱动轴密封 (4) 。 拆卸时,可能损坏密封件。
Show/hide table
图 4 | g00624675 |
- 拆下六个螺栓 (5) 和锁紧垫圈。 从马达壳体拆下盖 (6) 。
Show/hide table
图 5 | g00624676 |
注: 标记马达壳体盖中的位置,以便安装。
- 注意定位销 (7) 的位置,以便安装。
Show/hide table
图 6 | g00624678 |
- 拆下冲洗阀板和小清洗器。
- 拆下 O 型密封圈 (9) 。
- 使用油封钩压缩护圈 (1) 和弹簧。 拆下销钉 (2) 。
Show/hide table
图 7 | g00624696 |
Show/hide table
图 8 | g00624692 |
Show/hide table
图 9 | g00624693 |
- 对另一个定位销11重复此步骤 。
- 如图所示,使用尖嘴钳并钳住中心销 (3) 。 避开衬套施加压力。 使用油封钩压缩护圈和弹簧。 拆下衬套 (4) 、弹簧和护圈 (1) 。
Show/hide table
图 10 | g00624694 |
- 拆卸中心销 (3) 、衬套 (4) 、弹簧和护圈 (1) 。
Show/hide table
图 11 | g00624695 |
- 利用工具 (B) 以从马达壳体拆下旋转总成。
Show/hide table
图 12 | g00624704 |
- 从旋转总成 (14) 上拆下工具 (B) 。
Show/hide table
图 13 | g00624706 |
注: 标记缸筒中活塞的位置。
- 拉驱动轴和活塞组件 (16) 的柱塞缸 (15) 。
- 从油缸筒 (15) 内的中心销孔中拆下蝶形垫圈 (17) 和垫片 (18) 。
注: 标记蝶形垫圈 (17) 的位置。
- 如图所示,使用一段管或木质垫块以定位驱动轴和活塞组件。
Show/hide table
图 14 | g00624707 |
- 从挡板 (20) 拆下外侧活塞 (19) 。
注: 此时中心活塞不能拆下。
- 检查 (X) 区域上的所有活塞有无划痕或点蚀。 如有必要,更换活塞。
Show/hide table
图 15 | g00624708 |
- 如有必要,使用螺丝刀从活塞上卸下活塞环 (21) 。
- 卸下将挡板固定在驱动轴组件中的 7 个螺钉 (22) 。
Show/hide table
图 16 | g00624719 |
- 卸下挡板、中心销 (23) 和固定中心销的防松垫圈。
- 检查中心销 (23) 有无划痕或点蚀。 如有必要,更换中心销。
- 利用工具 (C) 以从轴上拆下扳手螺母 (24) 。
Show/hide table
图 17 | g00624722 |
- 适当按压从轴 (24) 上拆下两个轴承 (25) 和环 (26) 。
Show/hide table
图 18 | g00624723 |
Caterpillar Information System:
D9R Track-Type Tractor Machine Systems Steering Motor - Install
D9R Track-Type Tractor Machine Systems Steering Motor - Remove
D9R Track-Type Tractor Machine Systems Governor Control Linkage and Decelerator - Install
D9R Track-Type Tractor Machine Systems Governor Control Linkage and Decelerator - Remove
D9R Track-Type Tractor Machine Systems Bulldozer and Tilt Control Linkage - Remove
D9R Track-Type Tractor Machine Systems Bulldozer and Tilt Control Linkage - Install
D9R Track-Type Tractor Machine Systems Quick-Drop Valve - Remove
D9R Track-Type Tractor Machine Systems Quick-Drop Valve - Install
D9R Track-Type Tractor Machine Systems Quick-Drop Valve - Disassemble
D9R Track-Type Tractor Machine Systems Quick-Drop Valve - Assemble
D9R Track-Type Tractor Machine Systems Hydraulic Control Valve - Remove
D9R Track-Type Tractor Machine Systems Hydraulic Control Valve - Install
D9R Track-Type Tractor Machine Systems Steering Motor - Assemble
D9R Track-Type Tractor Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
D9R Track-Type Tractor Machine Systems Air Conditioner and Heater Fan Motor - Remove and Install
D9R Track-Type Tractor Machine Systems Air Conditioner Dryer - Remove and Install
D9R Track-Type Tractor Machine Systems Refrigerant Compressor - Remove and Install
D9R Track-Type Tractor Machine Systems Refrigerant Condenser - Remove and Install
3046 Engine For Caterpillar Built Machines Housing (Front) - Install
623F Wheel Tractor-Scraper Power Train Retarder Hydraulic Control Valve - Disassemble
994D Air System Wheel Loader Air Dryer - Check
545 Wheel Skidder Hydraulic and Steering System Steering Cylinder
515 Wheel Skidder and 525 Wheel Skidder Transmission and Grapple Electronic Control System Start Switch (Key)
623F Wheel Tractor-Scraper Power Train Retarder Hydraulic Control Valve - Assemble