Engine Oil Pump - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
B | 1P-0510 | Driver Group | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (B) to install bearings (10) in the oil pump body. The position of the bearing joint must be within 30 ± 15° of the centerline. The bearings must be installed so that the bearings are flush with the oil pump housing.
Show/hide table
Illustration 2 g01092850 - Apply clean engine oil to the inside diameter of the bearings in the oil pump body. Apply clean engine oil to shaft assemblies (9).
- Install shaft assemblies (9) in the oil pump housing.
Show/hide table
Illustration 3 g01092987 - Use Tooling (B) to install bearings (8) in cover (4), if the cover is equipped with bearings. The position of the bearing joint must be within 30 ± 15° of the centerline. The bearings must be installed so that the bearings are flush with the cover. Apply clean engine oil to the inside diameter of each bearing.
Show/hide table
Illustration 4 g01092829 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install cover (4) on the oil pump housing.
- Install plunger (5) and spring (6) in the oil pump housing. Install retainer (7).
Show/hide table
Illustration 5 g00573424 - Install key (3).
Show/hide table
Illustration 6 g00573401 - Install gear (2) on the oil pump shaft. Install bolt (1) and tighten the bolt to a torque of
55 ± 10 N·m (41 ± 7 lb ft) . - The engine oil pump must turn freely after assembly.
Show/hide table
Illustration 1 | g01196726 |
End By:
- Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar Information System:
C15 and C18 Industrial Engines Water Pump - Install
C15 and C18 Industrial Engines Water Pump - Remove
2004/08/01 A New Exhaust Seal is Used {1059}
C15 and C18 Industrial Engines Engine Oil Cooler - Install
C15 and C18 Industrial Engines Engine Oil Cooler - Remove
3412E, C30 and C32 Marine Engines Engine Oil Pump - Disassemble
3412E, C30 and C32 Marine Engines Engine Oil Pump - Remove
C15 and C18 Industrial Engines Engine Oil Filter Base - Install
C15 and C18 Industrial Engines Engine Oil Filter Base - Remove
G3612 and G3616 Engines Safety Messages
C15 and C18 Industrial Engines Electric Starting Motor - Remove and Install
3500B and 3500C Marine Engines Turbocharger Inlet Pressure Sensor
3508B, 3512B, and 3516B High Displacement Generator Sets Walk-Around Inspection
3508B Industrial Engines Engine Oil Temperature Sensor
3412E, C30 and C32 Marine Engines Engine Oil Pump - Install
2004/08/01 An Improved Injection Actuation Pressure Sensor Is Now Used {1925}
3500 Engines for Caterpillar Built Generator Sets Prelube Pressure Switch
EMCP3 Component Location
EMCP3 Digital Input Programming
EMCP3 Spare Analog Input Programming
2004/08/01 An Improved Injection Actuation Pressure Sensor Is Now Used {1925}
C9 Marine Engines and C9 Marine Generator Sets Alternator and Regulator
C9 Marine Engines and C9 Marine Generator Sets Alternator and Regulator
Installation of the Uninterruptible Power Supply (Single-Module System){4480} Installation of the Uninterruptible Power Supply (Single-Module System){4480}