UNEXPECTED TRANSMISSION SPEED CHANGE MAY OCCUR ON MACHINES EQUIPPED WITH THE FOLLOWING SHIFT LEVERS: 192-6334 CONTROL GP - TRANSMISSION, 201-0213 CONTROL GP - TRANSMISSION
Usage:
WHEEL LOADERS
950F II (4DJ02000-UP,5SK,8TK),
960F (9ZJ,4CL,6XL,1YM),
966F II (4YG,8BG,3XJ,9YJ,1SL),
970F (7SK,9JK,7PL),
980F II (5XJ588-UP,4RN,8JN) WHEEL LOADERS;
814F (9DM),
815F (1GN),
816F (5FN) 800 SERIES TRACTORS;
IT38F ( 6FN,5DR) INTEGRATED TOOL CARRIERS
WHEEL-TYPE TRACTORS
COMPACTORS
INTEGRATED TOOL CARRIERS
938F (1KM,2RM,8SM,6FN,7SN,5DR),950F II (4DJ02000-UP,5SK,8TK),
960F (9ZJ,4CL,6XL,1YM),
966F II (4YG,8BG,3XJ,9YJ,1SL),
970F (7SK,9JK,7PL),
980F II (5XJ588-UP,4RN,8JN) WHEEL LOADERS;
814F (9DM),
815F (1GN),
816F (5FN) 800 SERIES TRACTORS;
IT38F ( 6FN,5DR) INTEGRATED TOOL CARRIERS
Problem:
Field reports indicate that an unexpected transmission speed change may occur when either the machine's horn or window wiper switches are operated.
Solution:
Caterpillar Engineering is aware of this problem and a solution to this problem is being investigated. In the meantime, when a transmission control (shift lever) is service replaced by one of the listed part numbers, confirm that the operation of the horn or window wiper switches does not cause the transmission to change speeds. Perform the following procedure:
- 1.When a new shifter is installed, ensure that the wire from the horn switch is not wrapped around the wires from the shifter. The horn wire must be routed parallel to the shifter wiring.
- 2.Park the machine on a level surface. Apply the parking brake. Start the engine.
- 3.Use the "Auto/Manual" switch to select the manual mode.
- 4.Apply the service brake. Release the parking brake.
- 5. Place the shift lever in 4F.
- 6. Operate the horn.
- 7.Observe the actual transmission gear display. The actual transmission gear display is located on the monitoring system main module.
- 8.Operate the front window wipers and the rear window wipers simultaneously.
- 9.Observe the actual transmission gear display. The actual transmission gear display is located on the monitoring system main module.
- 10.Repeat Step 4 through Step 7 for 3F, 2F, and 1F. Repeat Step 4 through Step 7 for 3R, 2R, and 1R.
- 11.If the gear display changes while operating either the horn or the window wipers, do not put the machine back into service. Contact a Caterpillar Electronics Machine Analyst at (309) 578-6529 for further assistance.
COPYRIGHT 2001 CATERPILLAR ALL RIGHTS RESERVED
Caterpillar Information System:
Incorrect Assembly Instructions For Rod Seals In Hydraulic Cylinders Incorrect Assembly Instructions For Rod Seals In Hydraulic Cylinders
Failure Of The Number 7 Clutch In The Transmission Failure Of The Number 7 Clutch In The Transmission
New 17-Digit Serial Number Effective On M Series Tractor New 17-Digit Serial Number Effective On M Series Tractor
Transmission Oil Filter Retainer Is Not Retained Transmission Oil Filter Retainer Is Not Retained
Correct Operation Of Machines Equipped With "On Demand Fan" Correct Operation Of Machines Equipped With "On Demand Fan"
Loose Rocker Arm Nuts On The Fuel Injectors Loose Rocker Arm Nuts On The Fuel Injectors
Nuts Holding Transmission Output Shield Assembly May Loosen Nuts Holding Transmission Output Shield Assembly May Loosen
Paralleling Generators To Utility Substations Paralleling Generators To Utility Substations
Service Information Plates (3E-8154) Are Incorrectly Stamped Service Information Plates (3E-8154) Are Incorrectly Stamped
Electronic Control Module Software Change Electronic Control Module Software Change
Interference Occurs Between The Coupler And The Work Tool Interference Occurs Between The Coupler And The Work Tool
Track Roller Caps May Crack - Revised Track Roller Caps May Crack - Revised
MAINFRAME INSPECTION MAINFRAME INSPECTION
7T-1664 Torque Converter Bearing Cages May Not Assemble Correctly 7T-1664 Torque Converter Bearing Cages May Not Assemble Correctly
1T-1235 Torque Converter Freewheel Cams May Not Assemble Correctly 1T-1235 Torque Converter Freewheel Cams May Not Assemble Correctly
Rack Stops On The Loader Linkage May Not Contact Correctly Rack Stops On The Loader Linkage May Not Contact Correctly
Axle Oil Cooler Fan Motor Seal Failures Axle Oil Cooler Fan Motor Seal Failures
Aftercooler Radiator Cores Vent Line Connection To Shunt Tank Aftercooler Radiator Cores Vent Line Connection To Shunt Tank
Powertrain Oil Cooler Inlet Water Hose May Fail Powertrain Oil Cooler Inlet Water Hose May Fail
163-3992 Power Train Software Needs To Be Replaced On Certain 621, 623, And 627 Wheel Tractor Scrapers 163-3992 Power Train Software Needs To Be Replaced On Certain 621, 623, And 627 Wheel Tractor Scrapers
Low Level Leakage Experienced With The New Caterpillar Yellow Rod Seals Low Level Leakage Experienced With The New Caterpillar Yellow Rod Seals
Position Adjustment To Eliminate Battery Cable Interferences Position Adjustment To Eliminate Battery Cable Interferences
DAMAGED OR LOST 184-9866 BUCKET DUMP STOP ASSEMBLIES REQUIRE REPLACEMENT AND RECALIBRATION OF THE TILT LINKAGE POSITION SENSOR. DAMAGED OR LOST 184-9866 BUCKET DUMP STOP ASSEMBLIES REQUIRE REPLACEMENT AND RECALIBRATION OF THE TILT LINKAGE POSITION SENSOR.
New Caterpillar Yellow Cylinder Seals Provide Longer Service Life New Caterpillar Yellow Cylinder Seals Provide Longer Service Life