Water Pump - Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
由于端面密封损坏,水泵可能会泄漏。 轴和壳体之间的相对移动可能会使传动轴接触到水泵上的端面密封。 如果发生接触,将损坏端面密封并导致过早发生故障。 |
- 安装前,请参阅专门说明书 , REHS9244,了解水泵的正确装卸步骤。
Show/hide table
图 1 g01053081 - 将适当的起吊设备连接到水泵 (4) 上。 将水泵 (4) 放置到位。 水泵的重量约为
45 kg (100 lb) 。Show/hide table图 2 g01053079 - 安装螺栓 (5)。
Show/hide table
图 3 g01053077 - 安装螺栓 (3)。 从水泵 (4) 上拆下适当的起吊设备。
Show/hide table
图 4 g01053075 - 定位管组件 (2)。 安装螺栓 (1)。
- 加注冷却系统。 有关正确步骤和要使用的冷却液,请参阅操作和保养手册。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
由于端面密封损坏,水泵可能会泄漏。 轴和壳体之间的相对移动可能会使传动轴接触到水泵上的端面密封。 如果发生接触,将损坏端面密封并导致过早发生故障。 |
- 安装前,请参阅专门说明书 , REHS9244,了解水泵的正确装卸步骤。
Show/hide table
图 5 g01127942 - 使用适当的起吊设备将水泵 (3) 放置到发动机上。 水泵 (3) 的重量约为
34 kg (75 lb) 。 - 安装螺栓 (9) 以便将水泵 (3) 固定到发动机上。 拆下适当的起吊设备。
Show/hide table
图 6 g01127935 - 安装螺栓 (7),以便将防护罩组件 (8) 固定到发动机上。
- 安装螺栓 (4),以便将适配器 (5) 和 O 形密封圈固定到水泵 (3) 上。
- 将管组件 (6) 连接至适配器 (5)。
- 将适配器 (2) 和密封垫连接至水泵 (3)。
- 连接软管组件 (1)。
- 加注冷却系统。 请参阅操作和保养手册, "冷却系统冷却液(DEAC)- 更换"。
Caterpillar Information System:
3412E and C30 Marine Engines Basic Engine
2004/03/01 New High Efficiency Oil Filters are Now Available {1308}
2004/03/01 New High Efficiency Oil Filters are Now Available {1308}
2004/03/22 New High Efficiency Oil Filters are Now Available {1308}
3500B and 3500C Marine Engines Engine Harness - Rigid Wiring Harness
C13, C15, and C18 Generator Set Engines General Information
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Water Pump - Remove
G3516B Engines Diagnostic Codes
C7 Engines for Caterpillar Built Machines Electronic Unit Injector - Test
3500B Engines Valve Cover Base - Remove and Install
C-15 Petroleum Engine Reference Material
G3500 Engines MID 018 - CID 0770 - FMI 09 Cat Data Link #2 communications
G3516B Engines MID 036 - CID 0145 - FMI 03 12 Volt DC Power Supply short to +batt
G3516B Engines MID 036 - CID 0145 - FMI 04 12 Volt DC Power Supply short to ground
C11 and C13 Petroleum Engines Fan Drive Bearing - Replace
3126B Petroleum Engine Belt Tensioner - Inspect
C13, C15, and C18 Generator Set Engines System Configuration Parameters
3126B Marine Engines Injection Actuation Pressure Sensor - Test
C12 Marine Engines Engine Oil Level Gauge - Calibrate
G3516B Engines MID 036 - CID 1719 - FMI 12 Generator Output Power Sensor malfunction
EMCP3 Voltage and Frequency Adjustment
G3408 and G3412 Engines Engine Oil and Filter - Change
D7G Series 2 and D7G Series II Track-Type Tractors Horn - Test
2004/04/01 Replacement of the Injection Actuation Pressure Control Valve {5051}