Rear Power Take-Off (RPTO) - Install - If Equipped
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1P-0520 | 冲头总成 | 1 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (A) 将套筒轴承 (12) 安装到飞轮壳体中。 套筒轴承上的裂缝位置应保持角度 (Y)，即距竖直中心线 15 ± 1 度。 轴承应安装至深度 (Z)，即
2.0 ± 0.5 mm (0.08 ± 0.02 inch) 。 - 将盖 (10) 和螺栓安装在飞轮壳体的背面。
Show/hide table
图 2 g01134279 - 使用工具 (A) 将套筒轴承 (11) 安装到飞轮壳体中。 套筒轴承上的裂缝位置应保持角度 (X)，即距竖直中心线 15 ± 1 度。 轴承应安装至深度 (Z)，即
2.0 ± 0.5 mm (0.08 ± 0.02 inch) 。 - 将盖 (9) 和螺栓安装在飞轮壳体的背面。
Show/hide table
图 3 g01134263 - 使用工具 (A) 将套筒轴承 (8) 安装到接头 (2) 中。 将 O 形密封圈安装在接头上。
Show/hide table
图 4 g01134262 - 将齿轮组件 (6) 和齿轮组件 (7) 安置在飞轮壳体中。
Show/hide table
图 5 g01115921 - 安置惰齿轮 (5) 和护圈组件 (4)。 安装螺栓 (3)。 拧紧螺栓 (3) 至扭矩为
100 ± 20 N·m (74 ± 15 lb ft) 。 - 使用清洁的发动机机油润滑接头上的 O 形密封圈。 将接头 (2) 安置在飞轮壳体上，安装螺栓 (1)。
Show/hide table
| |
| 图 1 | g01134277 |
结束:
- 安装飞轮。 请参阅拆解和组装, "飞轮 - 安装"。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove - If Equipped
C18 Marine Auxiliary Engines E198 Low Fuel Pressure
C9 Marine Auxiliary and Marine Generator Set Engines Diagnostic Codes
C13, C15, and C18 Generator Set Engines E197 High Engine Oil Temperature
G3500 Engines Detonation Sensors
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
C15 Engine Cooling System Coolant (ELC) - Change
C15 Engine Cooling System Coolant (DEAC) - Change
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
C18 Marine Auxiliary Engines E096 High Fuel Pressure
2003/12/01 New Procedures Will Increase Power Module Reliability {7273}
C9 Marine Auxiliary and Marine Generator Set Engines Air Inlet Heater Circuit - Test
C13, C15, and C18 Generator Set Engines E199 Low Coolant Temperature
C13, C15, and C18 Generator Set Engines E360 Low Engine Oil Pressure
C18 Marine Auxiliary Engines E361 High Engine Coolant Temperature
C18 Marine Auxiliary Engines E362 Engine Overspeed
C18 Marine Auxiliary Engines E363 High Fuel Temperature
Installation Instructions for the 240-0717 Engine Oil Lines Gp for the Hydraulic Electronic Unit Injector (HEUI) Pump{1307} Installation Instructions for the 240-0717 Engine Oil Lines Gp for the Hydraulic Electronic Unit Injector (HEUI) Pump{1307}
2003/12/01 Parts List for Prelube Pump Group Kits {1319}
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Remove
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Equipped with Rear Power Take-Off
C9 Marine Auxiliary and Marine Generator Set Engines Injection Actuation Pressure Control Valve Circuit - Test