Auxiliary Water Pump - Disassemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-1855 | Retaining Ring Pliers | 1 |
B | 1P-1861 | Retaining Ring Pliers | 1 |
C | 1P-0510 | Driver Group | 1 |
D | 1U-6400 | Three Jaw Puller | 1 |
E | 9S-9152 | Bearing Puller Gp | 1 |
F | 8S-6470 | Forcing Screw | 1 |
Start By:
- Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Your specific auxiliary water pump may vary. Refer to Parts Information for more information.
- Remove integral seal (9), if necessary.
- Remove bolts (1) and remove elbow (2). Remove O-ring seal (3) from the elbow.
- Remove bolts (10) and remove elbow (12). Remove O-ring seal (11) from the elbow.
- Remove nut (5) and washer (4). Use Tooling (D) to remove gear (8).
- Remove bolts (7) and remove cover (6).
Show/hide table
Illustration 2 g01033085 - Remove O-ring seal (22) from housing (15).
- Remove bolt (16). Remove the O-ring seal from the bolt.
- Use Tooling (F) to remove impeller (21) from shaft (19).
- Remove cam (17) from the housing.
- Remove stainless key (18) from the shaft.
- Remove bolts (14) and remove adapter (13) from housing (15).
- Use Tooling (C) and a suitable press to remove pump seal (20) from the adapter.
Show/hide table
Illustration 3 g01039021 - Use Tooling (B) to remove retaining ring (23) from housing (15).
- Use Tooling (A) to remove retaining ring (26) from shaft (19).
- Remove washer (25) and plate assembly (24).
- Use a suitable press to remove shaft (19) out of the water pump housing. Press on shaft (19) from the impeller end of the water pump housing.
Show/hide table
Illustration 4 g01039081 - Use Tooling (C) and a suitable press to remove pump seal assembly (27) from the housing.
Show/hide table
Illustration 5 g01033150 - Use Tooling (A) to remove retaining ring (28). Remove washer (29) from shaft (19).
- Use Tooling (A) to remove retaining ring (34). Remove washer (33) from shaft (19).
- Use Tooling (E) and a suitable press to remove ball bearing (30), spacer (32), and ball bearing (31) from shaft (19).
Show/hide table
Illustration 1 | g01032983 |
Caterpillar Information System:
C9.3 Marine Engine Auxiliary Water Pump - Install
G3500 Engines Self-Diagnostics
C7 PETROLEUM Petroleum Engine Auxiliary Water Pump - Assemble
C9.3 Marine Engine Auxiliary Water Pump - Remove
2003/11/01 Improved Exhaust Seal for the Exhaust Manifold {1059}
2004/01/01 An Updated Version of Troubleshooting Guide, SENR9698 is Now Available {1105, 1400}
C32 Marine Engine Fuel System
C32 Marine Engine Electronic Control System Components
C9 Marine Engines and C9 Marine Generator Sets Camshaft Gear - Remove and Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Load Cell - Remove and Install
Installation Guide for Particulate Trap Exhaust Filters{1091} Installation Guide for Particulate Trap Exhaust Filters{1091}
2003/12/01 New Gaskets in the Water Lines Groups {1380}
C32 Marine Engine Heat Exchanger
G3500 Engines Location of Components
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Mechanism
C27 and C32 Generator Set Engines Electronic Unit Injector Rocker Arm
Installation of the 5P-4889 O-Ring Seal for the Fuel Transfer Pump{1256} Installation of the 5P-4889 O-Ring Seal for the Fuel Transfer Pump{1256}
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Travel Motor Guard - Remove and Install
C32 Marine Engine Vibration Damper and Pulley
C18 Generator set and C18 Marine Engines Rocker Arm and Shaft - Install
C32 Marine Engine Crankshaft
EMCP3 Data Link
C9 Marine Engines and C9 Marine Generator Sets Fuel Cooler - Remove and Install
G3500 Engines Electrical Connectors and Functions