Fuel Cooler - Remove and Install
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Loosen clamps (1) and disconnect hose (2).
- Loosen clamps (12) and disconnect hose (13).
- Remove bolt (6) and the clip from bracket assembly (7).
- Disconnect tube assembly (3).
- Disconnect tube assembly (5).
- Remove bolts (10). Remove fuel cooler (9). Remove clips (4) and the grommets from the fuel cooler.
- Remove bolts (8) and bracket (11) from the cylinder block.
Show/hide table
Illustration 1 | g01033540 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position bracket (11) on the cylinder block and install bolts (8).
- Install the grommets and clips (4) on fuel cooler (9). Position the fuel cooler on the bracket and install bolts (10).
- Install the grommets and clips (4) on the fuel cooler. Position fuel cooler (9) and install bolts (10).
- Connect tube assembly (5).
- Connect tube assembly (3). Install the clip and bolt (6) on bracket assembly (7).
- Connect hose (13). Tighten clamps (12).
- Connect hose (2). Tighten clamps (1).
Show/hide table
Illustration 2 | g01033540 |
Caterpillar Information System:
EMCP3 Data Link
C32 Marine Engine Crankshaft
C18 Generator set and C18 Marine Engines Rocker Arm and Shaft - Install
C32 Marine Engine Vibration Damper and Pulley
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Travel Motor Guard - Remove and Install
Installation of the 5P-4889 O-Ring Seal for the Fuel Transfer Pump{1256} Installation of the 5P-4889 O-Ring Seal for the Fuel Transfer Pump{1256}
C27 and C32 Generator Set Engines Electronic Unit Injector Rocker Arm
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Mechanism
G3500 Engines Location of Components
C32 Marine Engine Heat Exchanger
C7 PETROLEUM Petroleum Engine Auxiliary Water Pump - Disassemble
C9.3 Marine Engine Auxiliary Water Pump - Install
G3500 Engines Electrical Connectors and Functions
G3500 Engines Electronic Service Tools
2003/11/01 Improved Remanufactured Electric Starting Motors are Now Available {1453}
C9 Marine Engines and C9 Marine Generator Sets Fuel Pressure Regulator - Remove and Install
Oil Renewal System Troubleshooting
C15 Petroleum Generator Set Engines Electronic Unit Injector - Test
C15 Petroleum Generator Set Engines Water Pump - Test
C7 PETROLEUM Petroleum Engine Gear Group (Front) - Remove
C7 PETROLEUM Petroleum Engine Gear Group (Front) - Install
G3500 Engines Engine Monitoring System
2003/11/01 The Air Shutoff Has Been Improved {1078}
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing