Turbocharger
Show/hide table
Illustration 1 | g03432065 |
Typical example Right side view of engine (2) High-pressure turbocharger (7) Low-pressure turbocharger |
Show/hide table
Illustration 2 | g01502594 |
Tightening sequence for flange of the turbocharger |
Use the following procedure to tighten the locknuts for the flange of the turbocharger:
Note: Apply 4C-5599 Anti-Seize Compound to the washer face and threads of the locknuts before assembly.
- Tighten locknut 1 through locknut 4 in a numerical sequence to 55 ± 5 N·m (41 ± 4 lb ft). Refer to 2.
- Again, tighten locknut 1 through locknut 4 in a numerical sequence to 55 ± 5 N·m (41 ± 4 lb ft).
(1) Opening pressure of the wastegate at 1.00 mm (0.039 inch) lift ... 196.4 kPa (28 psi)
(3) Torque for the bolt ... 6 ± 1 N·m (55 ± 9 lb in)
(4) Torque for the elbow ... 12.0 ± 1.5 N·m (105 ± 13 lb in)
Use the following procedure to tighten the clamp assembly (5) :
- Tighten the clamp assembly to 18 N·m (160 lb in).
- Loosen the clamp assembly to 6 N·m (55 lb in).
- Again, tighten the clamp assembly to 13.5 ± 1.0 N·m (120 ± 9 lb in).
(6) Torque for the compressor clamp assembly ... 13.6 ± 1.2 N·m (120 ± 11 lb in)
Caterpillar Information System:
C9 Urban Transit Bus Engine Engine Oil and Filter - Change
3044C Industrial Engine and Engines for Caterpillar Built Machines Troubleshooting
C15 On-highway Engine Crankshaft Rear Seal - Install
C15 On-highway Engine Crankshaft Rear Seal - Remove
C15 and C18 Petroleum Generator Sets Generator - Dry
2003/07/01 New Fractured Connecting Rod Has Been Released {1218}
2003/09/01 New Recommended Maintenance Intervals for Coolant and Thermostat Regulators {1350, 1355, 1395}
C4.4 Industrial Engine Engine Air Cleaner Service Indicator - Inspect
3456 Generator Sets Voltage Connections
C7 Engines for Combat and Tactical Vehicles Engine Oil Level - Check
C7 Engines for Combat and Tactical Vehicles Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C7 Engines for Combat and Tactical Vehicles Cooling System Coolant Extender (ELC) - Add
C15 On-highway Engine Air Lines
3114, 3116, and 3126 Engines for Caterpillar Built Machines Camshaft - Install
3456 Generator Sets Rotating Rectifier - Test
2003/08/01 An Improved Air Lines Group and Carburetor Groups Are Available {1071, 1266}
2012/10/26 Policy for the Reuse of the Turbocharger Turbine Housing {1065}
C15 On-highway Engine Flywheel Housing - Remove and Install
2003/07/01 Improved Auxiliary Pumps are Used {1371}
2003/07/01 Align the Balancer Gears {1204, 1206, 1220}
2003/07/01 Make Sure That the Shunt Tank's Filler Neck is Vented {1354, 1377}
2003/07/01 Policy for Reusing the Turbocharger Turbine Housing {1052, 1065, 7754}
2003/07/14 Policy for Reusing the Turbocharger Turbine Housing {1065}
C3.4 IND Industrial Engine Fuel System - Prime