Crankshaft Rear Seal - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
D | 5P-1733 | 密封定位器 | 1 |
5P-1737 | 螺栓 | 3 | |
9S-8858 | 螺母 (密封件安装工具) | 1 | |
6V-6143 | 密封件安装工具 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 必须同时更换曲轴后密封和承磨衬套。 一旦曲轴后密封与承磨衬套分开,不得再次使用这些部件。
- 在安装曲轴后密封和承磨衬套之前,请检查曲轴有无划痕。 此外,请检查曲轴表面是否有无可能引起失圆状况的变形。 使用抛光布以清除曲轴上的瑕疵。
- 清理曲轴外径和耐磨衬套内径。
注: 把曲轴后密封安装到发动机中,并使指示曲轴转动方向的箭头指向发动机后方。
- 使用工具 (D) 安装承磨衬套 (2) 和曲轴后密封 (1)。
Show/hide table
图 1 | g01636744 |
注: 在安装曲轴后密封和承磨衬套的过程中,请勿使用任何类型的润滑剂。
结束:
- 安装飞轮。 请参阅拆解和组装, "飞轮 - 安装"。
Caterpillar Information System:
C15 On-highway Engine Crankshaft Rear Seal - Remove
C15 and C18 Petroleum Generator Sets Generator - Dry
2003/07/01 New Fractured Connecting Rod Has Been Released {1218}
2003/09/01 New Recommended Maintenance Intervals for Coolant and Thermostat Regulators {1350, 1355, 1395}
C4.4 Industrial Engine Engine Air Cleaner Service Indicator - Inspect
3456 Generator Sets Voltage Connections
C7 Engines for Combat and Tactical Vehicles Engine Oil Level - Check
C7 Engines for Combat and Tactical Vehicles Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C7 Engines for Combat and Tactical Vehicles Cooling System Coolant Extender (ELC) - Add
C7 Engines for Combat and Tactical Vehicles Cooling System Coolant (ELC) - Change
2003/07/07 Optional High Efficiency Filters Are Now Available {3004, 5068}
C7 Engines for Combat and Tactical Vehicles Cooling System Coolant (DEAC) - Change
3044C Industrial Engine and Engines for Caterpillar Built Machines Troubleshooting
C9 Urban Transit Bus Engine Engine Oil and Filter - Change
C15 On-highway Engine Turbocharger
C15 On-highway Engine Air Lines
3114, 3116, and 3126 Engines for Caterpillar Built Machines Camshaft - Install
3456 Generator Sets Rotating Rectifier - Test
2003/08/01 An Improved Air Lines Group and Carburetor Groups Are Available {1071, 1266}
2012/10/26 Policy for the Reuse of the Turbocharger Turbine Housing {1065}
C15 On-highway Engine Flywheel Housing - Remove and Install
2003/07/01 Improved Auxiliary Pumps are Used {1371}
2003/07/01 Align the Balancer Gears {1204, 1206, 1220}
2003/07/01 Make Sure That the Shunt Tank's Filler Neck is Vented {1354, 1377}