Cylinder Head - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
B     | 5P-3931     | 防粘结剂     | -     |
C     | - (1)     | 镍基防咬合剂     | -     |
Show/hide table
( 1 ) | 有关制造商零件号,请参考技术信息公告, TIBU 5269。 |
- 将 O 形密封圈 (25) 和密封垫 (24) 安装在发动机缸体上。
Show/hide table
图 1 | g01086765 |
- 安装隔盘 (22) 。
Show/hide table
图 2 | g01086764 |
- 在隔盘 (22) 上安装缸垫 (19) 、密封件 (20) 、密封件 (21) 和 O 形密封圈 (23) 。
- 在缸盖 (4) 上固定工具 (A) 和适当的起吊设备。 缸盖 (4) 的重量约为 50 kg (110 lb)。
Show/hide table
图 3 | g01086762 |
Show/hide table
图 4 | g01086760 |
Show/hide table
图 5 | g01089250 |
- 定位缸盖 (4) 。
- 清洁螺栓 (17) 。
- 将清洁的发动机机油涂抹在螺栓 (17) 的螺纹上,然后安装螺栓 (17) 。
- 按照数字顺序依次拧紧螺栓 (17) 至扭矩为 30 ± 5 N·m (22 ± 4 lb ft)。
- 按照数字顺序将螺栓 (17) 依次重新上紧到 270 ± 35 N·m (200 ± 26 lb ft) 的扭矩。
- 按照数字顺序将螺栓 (17) 依次重新上紧到 450 ± 20 N·m (330 ± 15 lb ft) 的扭矩。
- 用 55 ± 10 N·m (40 ± 7 lb ft)的扭矩拧紧螺栓 (18) 。
- 将密封垫置于缸盖 (4) 上。
- 连接适配器组件 (13) 。
Show/hide table
图 6 | g01086759 |
- 安装螺栓 (14) 。
- 安装 O 形密封圈和弯头 (16) 。
- 安装 O 形密封圈和弯头 (15) 。
- 将密封垫 (11) 和 O 形密封圈 (12) 定位在缸盖 (4) 上。
Show/hide table
图 7 | g01086757 |
- 将盖组件 (9) 定位于缸盖 (4) 上。
Show/hide table
图 8 | g01086755 |
- 安装螺栓 (10) 。
- 在缸盖 (4) 上定位排气歧管 (6) 和密封件。
Show/hide table
图 9 | g01086753 |
- 将卡箍 (8) 定位于排气歧管 (6) 上。
- 安装螺栓 (7) 。
- 将工具 (B) 涂抹在螺栓 (5) 上。 同时拧紧对角相对的螺栓 (5) ,要达到以下扭矩 55 ± 5N·m (41 ± 4 lb ft)。
- 如有必要,请在排气歧管 (6) 上安装热电偶。 安装之前先在热电偶上涂抹工具 (C) 。 如果热电偶为直式,拧紧螺母至扭矩为 25 ± 5 N·m (18 ± 4 lb ft)。 若热电偶有 90 度弯曲,拧紧螺母至扭矩为 12 ± 3 N·m (105 ± 27 lb in)。
- 安装护罩组件 (3) 。
Show/hide table
图 10 | g01086752 |
- 安装板 (2) 。
Show/hide table
图 11 | g01086750 |
- 安装螺栓 (1) 。
- 加注冷却系统。 请参阅操作和保养手册, "加注容量和建议"。
End By: 安装摇臂轴组件和推杆。 请参阅 拆解和组装, "摇臂轴和推杆 - 安装"。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Cylinder Head - Remove
Procedure for Tagging Rental Fleet {1000, 6000, 6700, 7000} Procedure for Tagging Rental Fleet {1000, 6000, 6700, 7000}
3500B and 3500C Marine Propulsion Engines Diagnostic Codes
G3500B Engines Electrohydraulic System Components
3618 Engine Starting Motor - Inspect
Product Link 151/201 Commands
G3500 Engines Air Starting System - Starting with an Air Prelube Pump
Product Link 151/201 Spare Input Configure
Product Link 151/201 Wireless Service Configure
Product Link 151/201 Report Parameters Configure
Product Link 151/201 Installation Parameters Configure
Product Link 151/201 Configuration
C1.5 and C2.2 Marine Generator Set Engines Engine Oil Line - Remove and Install
G3304 and G3306 Engines Magneto - Assemble
2003/10/06 Installation of the Correct Dust Seal in the Swing Gear and Bearing {7063}
3406C Generator Sets Safety Messages
Installation of Double Lip Wiper Seal{7562} Installation of Double Lip Wiper Seal{7562}
3406C Generator Sets Model View Illustrations
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0091 - FMI 13 Throttle Position calibration required
Recommendations for Caterpillar Gas Engine Cooling Systems{1350} Recommendations for Caterpillar Gas Engine Cooling Systems{1350}
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0277 - FMI 08 Timing Calibration signal abnormal
3054C Industrial Engine Idler Gear - Remove and Install - Bosch EPVE Fuel Injection Pump
G3520C and G3520E Generator Set Engines Thermostatic Valve - Disassemble
G3520C and G3520E Generator Set Engines Thermostatic Valve - Assemble