Cylinder Head - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
开始:
- 拆下摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 请参阅操作和保养手册, "加注容量和建议"。
- 拆下螺栓 (1) 。
Show/hide table
图 1 | g01086750 |
- 拆下板 (2) 。
注: 需要拆卸不止一块板。
- 拆卸护罩组件 (3) 。
Show/hide table
图 2 | g01086752 |
- 如有必要,请从排气歧管 (6) 上拆卸热电偶。
Show/hide table
图 3 | g01086753 |
- 卸下螺栓 (5) 。
- 拆卸螺栓 (7) ,然后从排气歧管 (6) 上拆下卡箍 (8) 。
- 从缸盖 (4) 上拆下排气歧管 (6) 和密封件。
- 拆下螺栓 (10) 后,将盖组件 (9) 从缸盖 (4) 上拆下。
Show/hide table
图 4 | g01086755 |
- 从缸盖 (4) 上拆下密封垫 (11) 和 O 形密封圈 (12) 。
Show/hide table
图 5 | g01086757 |
- 拆下弯头 (15) 和 O 形密封圈。
Show/hide table
图 6 | g01086759 |
- 拆下弯头 (16) 和 O 形密封圈。
注: 拆下弯头 (16) ,以便可以接近螺栓 (14) 。
- 拆下螺栓 (14) 以断开适配器组件 (13) 。
- 将密封垫从缸盖 (4) 上拆下。
Show/hide table
图 7 | g01086760 |
- 从缸盖 (4) 上卸下螺栓 (17) 。
- 在缸盖 (4) 上固定工具 (A) 和适当的提升装置。 缸盖 (4) 的重量约为 50 kg (110 lb)。
Show/hide table
图 8 | g01086762 |
- 拆下螺栓 (18) 。
- 拆下缸盖 (4) 。
- 从隔盘 (22) 上拆下缸垫 (19) 、密封件 (20) 、密封件 (21) 和 O 形密封圈 (23) 。
Show/hide table
图 9 | g01086764 |
- 拆下隔盘 (22) 。
- 从发动机缸体上拆下 O 形密封圈 (25) 和密封垫 (24) 。
Show/hide table
图 10 | g01086765 |
Caterpillar Information System:
Procedure for Tagging Rental Fleet {1000, 6000, 6700, 7000} Procedure for Tagging Rental Fleet {1000, 6000, 6700, 7000}
3500B and 3500C Marine Propulsion Engines Diagnostic Codes
G3500B Engines Electrohydraulic System Components
3618 Engine Starting Motor - Inspect
Product Link 151/201 Commands
G3500 Engines Air Starting System - Starting with an Air Prelube Pump
Product Link 151/201 Spare Input Configure
Product Link 151/201 Wireless Service Configure
Product Link 151/201 Report Parameters Configure
Product Link 151/201 Installation Parameters Configure
Product Link 151/201 Configuration
Product Link 151/201 Setup
G3520C and G3520E Generator Set Engines Cylinder Head - Install
C1.5 and C2.2 Marine Generator Set Engines Engine Oil Line - Remove and Install
G3304 and G3306 Engines Magneto - Assemble
2003/10/06 Installation of the Correct Dust Seal in the Swing Gear and Bearing {7063}
3406C Generator Sets Safety Messages
Installation of Double Lip Wiper Seal{7562} Installation of Double Lip Wiper Seal{7562}
3406C Generator Sets Model View Illustrations
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0091 - FMI 13 Throttle Position calibration required
Recommendations for Caterpillar Gas Engine Cooling Systems{1350} Recommendations for Caterpillar Gas Engine Cooling Systems{1350}
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0277 - FMI 08 Timing Calibration signal abnormal
3054C Industrial Engine Idler Gear - Remove and Install - Bosch EPVE Fuel Injection Pump
G3520C and G3520E Generator Set Engines Thermostatic Valve - Disassemble