Diagnostic Codes
诊断代码用来为操作员提供故障警示。 诊断编码可向维修技师指示故障的性质。 诊断代码由以下识别符组成:模块识别符(MID), 部件识别符(CID) 和 故障模式识别符(FMI)。 DID 用来指出产生诊断代码的电子模块。 发动机主电子控制模块(ECM)的 MID 是 36。 发动机辅助电子控制模块(ECM)的 MID 是 47。 CID 用来指出系统内的部件。 FMI 用来指出当前的故障模式。 诊断代码可在 Caterpillar 电子技师(ET)上查看。 不要混淆诊断代码和诊断事件。
激活的诊断代码
激活的诊断代码代表电子控制系统存在的故障。 尽快地排除故障。 产生激活诊断代码时,电子监控系统(EMS)等显示模块可能产生警告。
Show/hide table
图 1 | g00740986 |
典型实例 |
图 1 显示了冷却液温度传感器的典型输出电压。 可以利用 Cat ET 监视任何传感器的输出电压和温度。 Cat ET 将显示与传感器有关的诊断代码。 如图 1 中所示,请记下传感器的输出电压。 当 ECM 检测到来自传感器的异常输出电压时,将产生诊断代码。
注: 在调查和排除产生代码的故障之后,一定要清除所记录的诊断代码。
记录的诊断代码
当 ECM 产生诊断代码时,ECM 将此代码记录在永久存储器中。 ECM 内部有一个诊断时钟。 ECM 将记录首次产生诊断代码的小时数。 ECM 将记录最后一次产生诊断代码的小时数。 ECM 将记录代码产生的次数。 此信息可作为诊断和排除间歇性故障时的重要指标。 某些诊断代码虽被记录,但却不影响操作员操作。 间歇性故障最有可能的原因是线路连接出故障或线路损坏。 第二最可能的原因是部件出故障。 最小可能原因是电子控制模块(ECM)故障。 重复记录的诊断代码可能表示故障需要进行特别调查。
如果故障现象持续出现的话,应使用正确程序对操作员所经历的故障现象进行故障诊断与排除。
Caterpillar Information System:
G3500B Engines Electrohydraulic System Components
3618 Engine Starting Motor - Inspect
Product Link 151/201 Commands
G3500 Engines Air Starting System - Starting with an Air Prelube Pump
Product Link 151/201 Spare Input Configure
Product Link 151/201 Wireless Service Configure
Product Link 151/201 Report Parameters Configure
Product Link 151/201 Installation Parameters Configure
Product Link 151/201 Configuration
Product Link 151/201 Setup
Product Link 151/201 System Installation
Product Link 151/201 Spare Input Installation
Procedure for Tagging Rental Fleet {1000, 6000, 6700, 7000} Procedure for Tagging Rental Fleet {1000, 6000, 6700, 7000}
G3520C and G3520E Generator Set Engines Cylinder Head - Remove
G3520C and G3520E Generator Set Engines Cylinder Head - Install
C1.5 and C2.2 Marine Generator Set Engines Engine Oil Line - Remove and Install
G3304 and G3306 Engines Magneto - Assemble
2003/10/06 Installation of the Correct Dust Seal in the Swing Gear and Bearing {7063}
3406C Generator Sets Safety Messages
Installation of Double Lip Wiper Seal{7562} Installation of Double Lip Wiper Seal{7562}
3406C Generator Sets Model View Illustrations
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0091 - FMI 13 Throttle Position calibration required
Recommendations for Caterpillar Gas Engine Cooling Systems{1350} Recommendations for Caterpillar Gas Engine Cooling Systems{1350}
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0277 - FMI 08 Timing Calibration signal abnormal